Toyota R engine

The Toyota R family was a series of inline-four gasoline automobile engines. Designed for longitudinal placement in such vehicles as the Celica and Hilux and in production from 1953 through 1997, usage faded out as many of Toyota's mainstream models moved to front-wheel drive. Overhead cam (OHC) versions featured a chain-driven camshaft.

History of the R family

R

File:1953 Toyota R Type engine.jpg

1953 Toyota R engine.

The R family was produced from 1953 through 1964, and was originally manufactured at the Toyota Honsha plant.

Bore and stroke was . In common with new engines of the time, it was made from cast iron (both the block and the head), water cooled, used a three bearing crank, 12V electrics and a side-mounted gear-driven camshaft controlling overhead valves via pushrods in a non-cross flow head (exhaust and inlet manifolds being on the same side of the engine). Induction was by a twin throat down-draft carburettor, the compression ratio was 8.0:1 and the total weight was . An LPG version, the R-LPG, was produced for the last two years.

The R engine was the Toyota engine used in the 1958 Toyota Crown, the first model to be exported to the United States. Road & Track was unimpressed with the engine on its introduction, noting that it idled quietly but was "not capable of very high revolutions per minute."

Code	Power	Torque	Years	Comments
R	at 4,400 rpm	at 2,600 rpm	1953–1964
R-LPG			1962–1964	LPG

Applications:

• 1953–1955 Toyota Super
• 1955–1956 Toyota Master
• 1955–1958 Toyota Crown

2R

The 2R family was produced from 1964 through 1971. It is a square engine, with bore and stroke of .

Again, an LPG version, the 2R-LPG, was produced alongside the gasoline version. Production had been gradually transferred from the original Honsha plant to the new Toyota Kamigo plant in 1968.

Code	Power	Torque	Years	Comments
2R	at 5,000 rpm	at 2,600 rpm	1964–1969
2R-LPG			1964–1969	LPG

Applications:

• 1964 – January 1970 Toyota Corona RT40/RT46V/RT50/RT56
• February 1970 – January 1971 Toyota Corona RT80/90/86V
• 1968–1971 Toyota Mark II
• Toyota Bus RH15B
• 1965–1967 Toyota Stout RK43/RK47
• Toyota ToyoAce PK41
• Toyota Hilux RN10

3R

File:Toyota 3R-C Engine.jpg

Toyota 3R-C engine

The 3R family was produced from 1959 through 1968. The bore is 88 mm and the stroke is 78 mm.

When introduced it had a 7.7:1 compression ratio. In 1960 the 3R was uprated to 8:1 and the 3R-B version was offered from 1960 through 1968 with the old 7.7:1 compression ratio. The 3R-C was introduced to comply with California emissions laws. The 3R-LPG variant was produced for the last five years.

Code	Power	Torque	Years	Comments
3R	at 4,600 rpm	at 2,600 rpm	1959–1960	7.7 CR
3R	at 5,000 rpm	at 3,400 rpm	1960–1968	8.0 CR
3R-B	at 4,600 rpm	at 2,600 rpm	1960–1968	7.7 CR
3R-C				emissions control – California
3R-LPG			1963–1968	LPG

Applications:

• 1963–1968 Toyota Dyna
• 1964–1967 Toyota Stout, originally
• 1969–? Toyota Hilux
• 1967–1969 Toyota Corona (US)
• 1959–1967 Toyota Crown
• 1960–1967 Toyopet Masterline

4R

The 4R family was produced from 1965 through 1968.

Bore and stroke was .

Applications:

• 1967 Toyota 1600S (Japan)

5R

The 5R family was produced from 1968 through 1986. An LPG version, the 5R-LPG, was produced from 1968 through 1983.

It is a 2-valve OHV engine. Cylinder bore and stroke are . Output was at 5200 rpm and at 3000 rpm. Trucks such as the Dyna received a version tuned for torque, with a maximum power of at 4600 rpm and torque of at 3000 rpm.

Applications:

• Toyota Crown: third through sixth generation (RS50, RS60/66, RS80/RS100, and RS110). Only with LPG for taxi use in the last two generations.
• 1969-1977 Toyota Coaster RU18/RU19
• Toyota Dyna RU10/RU20/RU30
• Toyota Stout RK101
• Toyota ToyoAce RY20
• Aug 1981–? Toyota Corona sixth generation (RT131), only LPG combined with automatic transmission.

6R

The 6R was produced from 1969 through 1974. Output is at 5,300 rpm. The 6R-B was produced those same years, while the natural gas powered 6R-LPG was produced from 1970 through 1973.

Applications

• Sep 1970 – Jul 1973 Toyota Corona RT84/94
• Jan 1972 – Aug 1973 Toyota Mark II RX16V –

7R

The 7R was produced from 1968 through 1971 with a twin throat down-draft carburettor.
The 7R-B was produced from 1968 through 1969 with dual SU carburetors and higher compression.
The 7R-LPG was produced from 1969 through 1970.

The 7R was similar in displacement and technology to the 4R except the wider bore and shorter stroke of the 7R gave different power characteristics.

Code	Power	Torque	Compression	Years	Comments
7R	at 5,500 rpm	at 3,800 rpm	8.5	1968–1971
7R-B	at 6,200 rpm	at 4,200 rpm	9.5	1968–1969	Dual SU carburettors
7R-LPG				1969–1971	LPG

Applications:

• 1968–1970 Toyota Corona (RT41 sedan, RT53 hardtop, RT54 hardtop)
• 1970 Toyota Corona (RT82 sedan)
• 1968–1970 Toyota Corona Mark II (RT6x)
• 1968–1971 Toyota Corona Mark II Wagon (RT76D)

8R

File:8R engine in a 1971 Toyota Hilux.jpg

Toyota 8R engine in a Hilux

The 8R The engine was produced from 1968 through 1973.
Cylinder bore and stroke was with a five bearing crank.
It was also available as the 8R-D, dual SU 8R-B, EFI 8R-E, Californian-spec 8R-C and DOHC 8R-G.

It was a major departure for the R family. With a 2-valve SOHC head, it impressed contemporary reviewers – Road & Track praised its quietness and free-revving nature.

The 8R engine has a closed chamber head vs the open chamber of the 18R-C. The 8R-B has dual side draft SU-type Aisan carburettors with the float bowl under the body and vacuum activated power valves with strangle plates for chokes and liquid cooled intake with a balance tube.

Toyota upped the ante again with the DOHC (but still 2-valve) 8R-G, produced from 1969 through 1972. From 1969 to Feb 1971 it was known as the 10R, but along with a removal of the tensioner gear in the interest of quieter operation, it was renamed the 8R-G to reflect the decision that twin-cam engines were henceforth to be identified by a "-G" suffix. 4,931 twin cam engines were built, all installed in the Toyota Corona Mark II (RT72/75) 1900 GSS. The 10R/8R-G weighed in at and as such was both lighter and more compact than its less powerful predecessor the 9R

Code	Power	Torque	Compression	Years	Comments
8R	at 5,500 rpm	at 3,800 rpm	9.0	1968–1972
8R-B	at 6,000 rpm	at 4,000 rpm	10.0	1969–1971	Dual SU carburetors
8R-D
8R-E					EFI
8R-C	at 5,500 rpm	at 3,600 rpm	9.0		Californian emissions controls
8R-G	at 6,400 rpm	at 5,200 rpm		1969–1972	DOHC, dual side-draft carburettors

Applications:

• 1970–1971 Toyota Hilux,
• 1971–1973 Toyota Corona 1900 hardtop
• Toyota Corona Mark II RT72 Corona Mark II 1900 hardtop
• Toyota Corona Mark II RT72 Corona Mark II 1900 hardtop GSS (8R-G)

9R

File:Toyota 9R engine 02.jpg

Toyota 9R engine in a Corona

The 9R was produced from 1967 through 1968. Bore and stroke .

It was essentially a 4R with a DOHC head designed by Yamaha. The cam lobes activated the valves directly via a bucket over shim arrangement. This same arrangement was used on the 2M, 8R-G, 10R, 18R-G, 2T-G, 4A-GE and 3T-GTE engines (all designed by Yamaha).

Output was at 6,200 rpm and at 5,000 rpm. It was a 2-valve DOHC design with two Solex carburettors and weighed . A total of 2,229 9R engines were built.

Applications:

• Toyota Corona (RT55) 1600 GT hardtop

10R

The twin cam 10R was produced from 1967 through Feb 1971, when it was renamed the 8R-G. The later 8R-G version did not receive a timing chain tensioner in an effort to make it more silent.

Output was at 6,400 rpm and at 5,200 rpm.

Applications:

• Toyota Corona Mark II RT75 Corona Mark II GSS

12R

The 12R was produced from 1969 through 1988. It was also built in the Philippines as the 12R-M, by Toyota's local affiliate Delta Motors Corporation.
Technical Specs (Finnish Owner's Manual from 1973 Corona Mark 1)
– Four cylinder, 4-stroke, OHV
– Bore × stroke:
– Compression ratio: 8.5:1
– Maximum power: at 5400 rpm SAE

The 12R-LPG, was produced from 1969 through 1983.
Technical Specs: 1975 redline 4,400 rpm

Applications:

• 1971–1978 Toyota Corona
• 1971–1972 Toyota Hilux
• 1977 Toyota Hiace
• 1975 Toyota Hiace Commercial Camper
• 1976 Daihatsu Taft (F20)
• Delta Mini Cruiser/Explorer

16R

The OHC 16R was produced from 1974 through 1980. Power output as mounted in a 1980 Mark II was at 5,600 rpm, while a twin carburetted version produced at 6,000 rpm. The 16R-B was produced for the first two years. There was also a 16R-J version for various commercial vehicle applications.

Applications:

• October 1975 – February 1977 Toyota Carina RA10/16
• Toyota Mark II Van RX37V (16R-J),
• Toyota Corona RT102/112/117 (sedan/hardtop/wagon)
• Toyota Corona RT108V (van; 16R-J)
• Toyota Corona RT137V (van; 16R-J)
• Toyota HiAce RH12/14/17/41 (16R-J)

18R

File:1974 Toyota Celica engine (5948543051).jpg

Toyota 18R-C engine in a Celica

The 18R series shared a block; cylinder bore and stroke was .

The 2-valve, SOHC versions were as follows:

Code	Power	Torque	Years	Comments
18R	at 5000 rpm	at 3600 rpm	1971–1981  ?	non-emissions Hilux
18R-C	at 5500 rpm	at 3600 rpm	1971–1981	emissions control – worldwide (Californian Standards)
18R-U	at 5500 rpm	at 3600 rpm	1975–1978	emissions control – Japan
18R-E	at 5600 rpm	at 4400 rpm	1974–1975	EFI, Japan only

File:Toyota 18R-E engine.jpg

Japan only 18R-E in a Carina

Applications:

• 18R/18R-C/18R-U/18R-E
  • 1972 Toyota Corona 2000
  • 1972 Toyota Corona 2000 MK. II
  • 1972 Toyota Celica 2000
  • 197X Toyota Cressida 2000/Gen1
  • Toyota Hilux, 89 PS
• 18R-C
  • 1972–1974 Toyota Hilux,
  • 1974–1981 Toyota Celica 2000
  • 1980–1981 Toyota Corona Liftback (RT132, Australia)

18R-G

File:18R-GUengine.jpg

18R-G on an engine stand

The 2-valve DOHC 18R-G and its variations were produced from 1973 to 1982, replacing the 8R-G and providing a performance engine which took advantage of the entire 2-litre limit of Japan's "small car" class. While most 18R-Gs had a head designed and made by Yamaha, a very few had Toyota heads. Yamaha's tuning-fork logo can be seen on the Yamaha heads. Except for the head and related timing components, most parts were shared or interchangeable with the SOHC 18R. Combustion chambers were hemispheric.

File:18rg.jpg

18R-G in an engine bay

In 1975, air injection was added to the Japan-market 18R-GR for improved emissions. This used Solex carburettors. A fuel injected and catalyzed Japan-market version, the 18R-GEU, was produced from 1978 through 1982. There was also a catalyzed carburetted version, the 18R-GU.

File:Bigmikemunizrallycar.jpg

1973 TE27 Rally Car with a 152E TRD Race Engine

Code	Power	Torque	Years	Weight	Comments
18R-G	at 6400 rpm	at 5200 rpm	1972–1981
18R-GR	at 6400 rpm	at 4800 rpm	1973–1975		low compression for regular fuel
18R-GU	at 5800 rpm	at 4800 rpm	1975–1978		emissions control – Japan.
18R-GEU	at 5800 rpm	at 4800 rpm	1978–1982		EFI, emissions control (Japan).

Applications:

• 1973–1981 Toyota Celica GT 2000
• 1982–1983 Toyota Celica GT 2000 (RA63)
• 1974–1983 Toyota Carina GT 2000
• 1978–1983 Toyota Celica Camry GT 2000
• 1973–1982 Toyota Corona GT 2000

152E

Competition versions of the 18R-G and -GE include those used in rally Celicas of the period, one of which finished second in the 1977 RAC Rally. These had 4-valve heads and were called 152E, they were of bore and stroke and (depending on the source). The Group 4 rally version of the 152E had two twin-choke carburettors, and developed at 9000 rpm. Higher tuned engines developed as much as at 9,200 rpm. German racing team Schnitzer also developed a turbocharged silhouette racing version of the Celica, to take on the Porsche 935. With a KKK turbocharger, the Group 5 Celica developed but reliability was less than satisfactory.

19R

The 2-valve SOHC 19R was produced from 1974 through 1977. Cylinder bore and stroke was . Its dimensions are the same as of the 18R, but it featured TTC-V, Toyota's licensed version of Honda's CVCC stratified charge combustion system. Output is . The 19R was a short-lived experiment by Toyota, and was only offered in Japanese market cars.

Applications:

• 1974–1977 Carina RA13/RA31
• 1974–1977 Corona RT103/RT123

20R

The 2-valve SOHC 20R was produced from 1975 through 1980. Cylinder bore and stroke was . Aluminum alloy heads were used.

Initial output was at 4800 rpm ( in California) and at 2,800 rpm. Power was down slightly from 1978 through 1979 at at 4800 rpm and at 2400 rpm. The final version, from 1979 through 1980, was down again at at 4800 rpm (still at in Canada) and at 2400 rpm.

The 20R and subsequent models featured important design changes relative to the earlier SOHC R-series engines. The head was changed from a reverse-flow to a cross-flow type with hemispherical combustion chambers and shorter valve rockers. The timing chain was strengthened. The lower block bearings were strengthened against wear, safeguarding oil pressure, and the stroke was lengthened. The changes increased torque substantially and shifted peak power and torque towards the lower speed range. The later R series engines did much to establish Toyota's reputation for reliability, which had previously been indifferent at best.

Applications:

• 1975–1980 Toyota Hilux
• 1975–1980 Toyota Celica (U.S. Version)
• 1975–1980 Toyota Corona (U.S. Version)
• Toyota Stout (RK110/111)
• Toyota Coaster (RB11)

21R

The 2-valve SOHC 21R was produced from 1978 through 1987. Cylinder bore and stroke are .

Output for export markets, largely unconstrained by emissions, was Template:Cvt DIN at 5,000 rpm and at 4,000 rpm. Air injection and federally compliant emissions equipment for the 21R-C (1982–1985) dropped power down to Template:Cvt SAE net at 5,000 rpm. The air-injected Japanese version, the 21R-U, produces Template:Cvt JIS at 5,200 rpm and at 3,600 rpm but dropped to Template:Cvt at 5,400 rpm and at 4,000 rpm in 1986.

Applications:

• 1978–1982 Toyota Carina RA46-A, RA56-A
• 1978–1981 Toyota Celica RA46-B
• 1981–1983 Toyota Celica RA60-B
• 1978–1983 Toyota Corona RT133
• 1978–1980 Toyota Cressida/Corona Mark II/Chaser RX40, RX41
• 1980–1983 Toyota Cressida/Corona Mark II RX60
• 1979–198? Toyota HiAce Wagon RH23G

22R

File:1989ToyotaHiluxSURF4x4-engine.jpg

22R-E engine fitted in a 1989 Hilux Surf

The 2-valve SOHC 22R was produced from 1981 through 1997.

Cylinder bore and stroke was .

Initial output was at 4,800 rpm and at 2,800 rpm. By 1990 the 22R was producing at 5,000 rpm and at 3,400 rpm.

The first fuel injected 22R-E engines appeared in August 1982. Output of these engines is commonly rated at at 4,800 rpm and at 2,800 rpm.

In 1985, the engine was significantly reworked, output was up to at 4,800 rpm and at 3,600 rpm. Many parts from the newer 22R/R-E are not compatible with those from the older pre-1985 engine. Non-compatible parts include the cylinder head, block, pistons and many of the associated parts such as the timing chain and cover, and water and oil pumps (although the oil pump internals are the same). These changes also affected the 22R, therefore one can consider the 85–95 22R-E as a fuel injected version of the 85–90 22R with only minor differences, if any.

Toyota swapped the dual-row timing chain used in older engines for a single-row chain with plastic guides in 1983. The new system reduced drag on the engine but introduced a new maintenance problem. After about of operation, the chain may stretch to the point that the hydraulic-operated chain tensioner cannot take up any more slack. The timing chain then impacts the plastic driver's side chain guide, breaking it within a short period of time and creating a noticeable chattering sound in the front of the engine, especially when cold. If the engine continues to be operated without the guide restraint, the chain will vibrate excessively on the driver's side and stretch rapidly. The result is any of several failure modes.

First, the loose chain will reduce ignition timing accuracy, which usually results in noticeably rough running. Second, it may jump a tooth on the drive sprocket or break entirely, which almost always results in major damage to an interference engine. Third, the stretched chain can slap against the side of the timing cover and wear through the metal into the coolant passage behind the water pump, resulting in major damage to both the oil and cooling systems (sometimes mis-diagnosed as a head gasket failure). The damaged aluminum timing cover is difficult to repair effectively and is typically replaced after such an event. Aftermarket timing-chain kits for the 22R/R-E typically include steel-backed guides that do not readily break even after the initial chain stretching has occurred, permitting the chain to run beyond the point without further incident. However, some Toyota mechanics will recommend the plastic guides as they will break when the timing chain is stretched; When the guides break a noticeable chatter is heard from the timing chain slapping on the cover, warning the operator of a worn timing chain.

The turbocharged 22R-TE (sold from late 1985 through 1988) produced at 4,800 rpm and at 2,800 rpm.

These engines are extremely well known for their durability, decent fuel efficiency and good low to mid range torque.

However, its weakness is high-end power. The 22R has a large displacement and a strong block, but its comparatively long stroke and restrictive head limit its use in high revving applications. Thus, the Toyota 18R-G, 2T-G, 4A-GE and 3S-GE 4-cylinder engines are better suited for performance applications.

A popular modification to the early 22R is to use a 20R head. Contrary to popular lore, the 20R head does not have smaller combustion chambers. The misunderstanding originated when the 22R came out and an advantage was its higher compression ratio, so swapping a 20R block with a 22R, there was a compression increase. The 20R head has straight ports, so can flow better than the 22R head, improving high RPM power. The 20R head is a simple bolt-on modification for the pre-1985 block, but also requires the use of the 20R intake manifold, making it almost impossible (there's a lot of matching necessary) to use with the 22R-E EFI system. For blocks 1985 and onwards, further modifications are required.

Code	Power	Torque	Years	Comments
22R	at 4,800 rpm	at 2,800 rpm	1981–1990	carb, dual row timing chain ('81–'82) carb, single row timing chain ('83–'90)
22R	at 5,000 rpm	at 3,400 rpm	1990–1995
22R-E	at 4,800 rpm	at 2,800 rpm	1983–1984	EFI, single row timing chain
22R-E	at 4,800 rpm	at 3,600 rpm	1985–1997	EFI, single row timing chain
22R-TE	at 4,800 rpm	at 2,800 rpm	1986–1988	turbocharged, single row timing chain

Applications:

• 22R
  • 1981-1982 Toyota Corona
  • 1981–1997 Toyota Hilux
  • 1981–1984 Toyota Celica
  • 1991 Toyota Cressida
  • 1981–1995 Toyota Pickup
  • 1984 Toyota 4Runner
  • 1984–1989 Toyota Land Cruiser II, Bundera
• 22R-E
  • 1985–1995 Toyota Hilux
  • 1983–1985 Toyota Celica
  • 1983–1987 Toyota Corona RT142
  • 1984–1995 Toyota Pickup
  • 1985–1995 Toyota 4Runner
  • 1989–1997 Volkswagen Taro
• 22R-TE
  • late 1985–1988 Toyota Hilux
  • 1986–1987 Toyota 4Runner

See also

• List of Toyota engines
• 22R Tech Notes (Toysport)
• Toyota 20R engines: details and photos (Toyoland)