Janka hardness test
The Janka hardness test (Template:IPAc-en;[1] Script error: No such module "IPA".), created by Austrian-born American researcher Gabriel Janka (1864–1932), measures the resistance of a sample of wood to denting and wear.Script error: No such module "Unsubst". It measures the force required to embed an Template:Convert steel ball halfway into a sample of wood. (The diameter was chosen to produce a circle with an area of 100 square millimeters, or one square centimeter.)[2]
A common use of Janka hardness ratings is to determine whether a species is suitable for use as flooring. For hardwood flooring, the test usually requires an Template:Cvt sample with a thickness of at least 6–8 mm, and the most commonly used test is the ASTM D1037. When testing wood in lumber form, the Janka test is always carried out on wood from the tree trunk (known as the heartwood), and the standard sample (according to ASTM D143) is at 12% moisture content and clear of knots.[3]
The hardness of wood varies with the direction of the wood grain. Testing on the surface of a plank, perpendicular to the grain, is said to be of "side hardness". Testing the cut surface of a stump is called a test of "end hardness".Script error: No such module "Unsubst". Side hardness may be further divided into "radial hardness" and "tangential hardness", although the differences are minor and often neglected.
The results are stated in various ways, leading to confusion, especially when the actual units employed are often not attached. The resulting measure is always one of force. In the United States, the measurement is in pounds-force (lbf). In Sweden, it is in kilograms-force (kgf), and in Australia, either in newtons (N) or kilonewtons (kN). This confusion is greatest when the results are treated as units, for example "660 Janka".[4]
The Janka hardness test results tabulated below followed ASTM D 1037-12 testing methods. Lumber stocks tested range from 1" to 2" (25–50 mm) thick. The tabulated Janka hardness numbers are an average. There is a standard deviation associated with each species, but these values are not given.Script error: No such module "Unsubst". No testing was done on actual flooring.
Other factors affect how flooring performs: the type of core for engineered floorings, such as pine, HDF, poplar, oak, or birch; grain direction and thickness; floor or top wear surface, etc. The chart is not to be considered an absolute; it is meant to help people understand which woods are harder than others.
Typical Janka hardness values
| Key |
|---|
| Hardwood |
| Softwood |
| Pseudowood |
References
- ↑ Script error: No such module "citation/CS1"..
- ↑ Script error: No such module "citation/CS1".
- ↑ Script error: No such module "citation/CS1".
- ↑ Script error: No such module "citation/CS1".
- ↑ Script error: No such module "citation/CS1".
- ↑ Script error: No such module "citation/CS1".
- ↑ Script error: No such module "citation/CS1".
- ↑ Script error: No such module "citation/CS1".
- ↑ Script error: No such module "citation/CS1".
- ↑ Script error: No such module "citation/CS1".
- ↑ Script error: No such module "citation/CS1".Template:Dead link
- ↑ Script error: No such module "citation/CS1".
- ↑ Script error: No such module "citation/CS1".
- ↑ Script error: No such module "citation/CS1".
- ↑ Script error: No such module "citation/CS1"..
- ↑ Script error: No such module "citation/CS1".
- ↑ Script error: No such module "citation/CS1".
- ↑ a b c Script error: No such module "Citation/CS1". The record softness of 22 lbf is often falsely ascribed to quipo, but all such reports appear to be a misreading of figures 15 and 16 from this primary source, which makes clear that measurement is of balsa, and the softest quipo measured was 46 lbf tangential, 38 lbf radial.