Fusible alloy

From Wikipedia, the free encyclopedia
(Redirected from Low-melting alloys)
Jump to navigation Jump to search

Template:Short description A fusible alloy is a metal alloy capable of being easily fused, i.e. easily meltable, at relatively low temperatures. Fusible alloys are commonly, but not necessarily, eutectic alloys.

Sometimes the term "fusible alloy" is used to describe alloys with a melting point below Script error: No such module "convert".. Fusible alloys in this sense are used for solder.

Introduction

Fusible alloys are typically made from low melting metals. There are 14 low melting metallic elements that are stable for practical handling. These are in 2 distinct groups: The 5 alkali metals have 1 s electron and melt between +181 (Li) and +28 (Cs) Celsius; The 9 poor metals have 10 d electrons and from none (Zn, Cd, Hg) to three (Bi) p electrons, they melt between -38 (Hg) and +419 (Zn) Celsius. From a practical view, low-melting alloys can be divided into the following categories:

A practical reason here is that the chemical behaviour of alkali metals is very distinct from poor metals. Of the 9 poor metals Hg (mp -38 C) and Ga (mp +29 C) have each their distinct practical issues, and the remaining 7 poor metals from In (mp +156 C) to Zn (mp +419 C) can be viewed together. Of elements which might be viewed as related but do not share the distinct properties of poor metals: Po is estimated to melt at 254 C and might be poor metal by properties but is too radioactive (longest halflife 125 years) for practical use; At same reasoning as Po; Sb melts at 630 C and is regarded as semimetal rather than poor metal; Te is also regarded as semimetal not poor metal; of other metals, next lowest melting point is Pu, but its melting point at 640 Celsius leaves a 220 degree gap between Zn and Pu, thus making the "poor metals" from In to Zn a natural group.

Some reasonably well-known fusible alloys are Wood's metal, Field's metal, Rose metal, Galinstan, and NaK.

Applications

Melted fusible alloys can be used as coolants as they are stable under heating and can give much higher thermal conductivity than most other coolants; particularly with alloys made with a high thermal conductivity metal such as indium or sodium. Metals with low neutron cross-section are used for cooling nuclear reactors.

Such alloys are used for making the fusible plugs inserted in the furnace crowns of steam boilers, as a safeguard in the event of the water level being allowed to fall too low. When this happens the plug, being no longer covered with water, is heated to such a temperature that it melts and allows the contents of the boiler to escape into the furnace. In automatic fire sprinklers the orifices of each sprinkler is closed with a plug that is held in place by fusible metal, which melts and liberates the water when, owing to an outbreak of fire in the room, the temperature rises above a predetermined limit.[1]

Bismuth on solidification expands by about 3.3% by volume. Alloys with at least half of bismuth display this property too.[2] This can be used for mounting of small parts, e.g. for machining, as they will be tightly held.Script error: No such module "Unsubst". Script error: No such module "labelled list hatnote".

Low-melting alloys and metallic elements

Well-known alloys

Template:Low melting point alloys

Other alloys

Script error: No such module "Labelled list hatnote". Starting with a table of component elements and selected binary and multiple systems ordered by melting point:

Low melting alloys and metallic elements
Composition in weight-percent Melting point Eutectic? Name or remark
Cs 73.71, K 22.14, Na 4.14 [3] Template:Cvt yes "CsNaK", reactive with water and air
Hg 91.5, Tl 8.5 Template:Cvt yes used in low-reading thermometers
Hg 100 Template:Cvt (yes)
Cs 77.0, K 23.0 Template:Cvt
K 76.7, Na 23.3 Template:Cvt yes
K 78.0, Na 22.0 Template:Cvt no NaK
Ga 61, In 25, Sn 13, Zn 1 Template:Cvt yes
Ga 62.5, In 21.5, Sn 16.0 Template:Cvt yes Galinstan alloy
Ga 69.8, In 17.6, Sn 12.5 Template:Cvt no Galinstan alloy
Ga 68.5, In 21.5, Sn 10 Template:Cvt no Galinstan alloy
Ga 75.5, In 24.5 Template:Cvt yes
Cs 100 Template:Cvt (yes)
Ga 100 Template:Cvt (yes)
Rb 100 Template:Cvt (yes)
Bi 40.3, Pb 22.2, In 17.2, Sn 10.7, Cd 8.1, Tl 1.1 Template:Cvt yes
Bi 40.63, Pb 22.1, In 18.1, Sn 10.65, Cd 8.2 Template:Cvt
Bi 44.7, Pb 22.6, In 19.1, Cd 5.3, Sn 8.3 Template:Cvt yes Cerrolow 117. Used as a solder in low-temperature physics.[4]
Bi 49, Pb 18, In 21, Sn 12 Template:Cvt ChipQuik desoldering alloy.[5] Cerrolow 136. Slightly expands on cooling, later shows slight shrinkage in couple hours afterwards. Used as a solder in low-temperature physics.[4] Lens Alloy 136, used for mounting lenses and other optical components for grinding.[6] Used for mounting small delicate oddly-shaped components for machining.
Bi 32.5, In 51.0, Sn 16.5 Template:Cvt yes Field's metal
K 100 Template:Cvt (yes)
Bi 50, Pb 26.7, Sn 13.3, Cd 10 Template:Cvt yes Cerrobend. Used in low-temperature physics as a solder.[4]
Bi 49.5, Pb 27.3, Sn 13.1, Cd 10.1 Template:Cvt yes Lipowitz's alloy
Bi 50.0, Pb 25.0, Sn 12.5, Cd 12.5 Template:Cvt yes Wood's metal
In 66.3, Bi 33.7 Template:Cvt yes [7]
Bi 42.5, Pb 37.7, Sn 11.3, Cd 8.5 Template:Cvt no Cerrosafe
Bi 57, In 26, Sn 17 Template:Cvt yes [7]
Bi 54, In 29.7, Sn 16.3 Template:Cvt yes [7]
Bi 56, Sn 30, In 14 Template:Cvt no ChipQuik desoldering alloy, lead-free
Bi 50, Pb 30, Sn 20, Impurities Template:Cvt no Lichtenberg's alloy,[8] also called Onions' Fusible Alloy[9]
Bi 52.5, Pb 32.0, Sn 15.5 Template:Cvt yes
Bi 52, Pb 32.0, Sn 16 Template:Cvt yes Bi52. Good fatigue resistance combined with low melting point. Reasonable shear strength and fatigue properties. Combination with lead-tin solder may dramatically lower melting point and lead to joint failure.[10]
Bi 50.0, Pb 31.2, Sn 18.8 Template:Cvt no Newton's metal
Na 100 Template:Cvt (yes)
Bi 50.0, Pb 28.0, Sn 22.0 Template:Cvt no Rose's metal
Bi 55.5, Pb 44.5 Template:Cvt yes
Bi 58, Sn 42 Template:Cvt yes Bi58. Reasonable shear strength and fatigue properties. Combination with lead-tin solder may dramatically lower melting point and lead to joint failure.[10] Low-temperature eutectic solder with high strength.[11] Particularly strong, very brittle.[12] Used extensively in through-hole technology assemblies in IBM mainframe computers where low soldering temperature was required. Can be used as a coating of copper particles to facilitate their bonding under pressure/heat and creating a conductive metallurgical joint.[13] Sensitive to shear rate. Good for electronics. Used in thermoelectric applications. Good thermal fatigue performance. Yield strength Script error: No such module "convert"., tensile strength Script error: No such module "convert"..[14]
Bi 57, Sn 43[15] Template:Cvt yes
In 100 Template:Cvt (yes) In99. Used for die attachment of some chips. More suitable for soldering gold, dissolution rate of gold is 17 times slower than in tin-based solders and up to 20% of gold can be tolerated without significant embrittlement. Good performance at cryogenic temperatures.[16] Wets many surfaces incl. quartz, glass, and many ceramics. Deforms indefinitely under load. Does not become brittle even at low temperatures. Used as a solder in low-temperature physics, will bond to aluminium. Can be used for soldering to thin metal films or glass with an ultrasonic soldering iron.[4]
Li 100 Template:Cvt (yes)
Sn 62.3, Pb 37.7 Template:Cvt yes
Sn 63.0, Pb 37.0 Template:Cvt no Eutectic solder. Sn63, ASTM63A, ASTM63B. Common in electronics; exceptional tinning and wetting properties, also good for stainless steel. One of the most common solders. Low cost and good bonding properties. Used in both SMT and through-hole electronics. Rapidly dissolves gold and silver, not recommended for those.[11] Sn60Pb40 is slightly cheaper and is often used instead for cost reasons, as the melting point difference is insignificant in practice. On slow cooling gives slightly brighter joints than Sn60Pb40.[17]

Yield strength Script error: No such module "convert"., tensile strength Script error: No such module "convert"..[18]

Sn 91.0, Zn 9.0 Template:Cvt yes KappAloy9 Designed specifically for Aluminum-to-Aluminum and Aluminum-to-Copper soldering. It has good corrosion resistance and tensile strength. Lies between soft solder and silver brazing alloys, thereby avoiding damage to critical electronics and substrate deformation and segregation. Best solder for Aluminum wire to Copper busses or Copper wire to Aluminum busses or contacts.[19] UNS#: L91090
Sn 92.0, Zn 8.0 Template:Cvt no Tin foil
Sn 100 Template:Cvt (yes) Sn99. Good strength, non-dulling. Use in food processing equipment, wire tinning, and alloying.[20] Susceptible to tin pest.
Bi 100 Template:Cvt (yes) Used as a non-superconducting solder in low-temperature physics. Does not wet metals well, forms a mechanically weak joint.[4]
Tl 100 Template:Cvt (yes)
Cd 100 Template:Cvt (yes)
Pb 100 Template:Cvt (yes)
Zn 100 Template:Cvt (yes) For soldering aluminium. Good wettability of aluminium, relatively good corrosion resistance.[21]

Then organized by practical group and alphabetic symbols of components: Most of the pairwise phase diagrams of 2 component metal systems have data available for analysis, like at https://himikatus.ru/art/phase-diagr1/diagrams.php Taking the pairwise alloys of the 7 poor metals other than Hg and Ga, and ordering the pairs (total 21) by alphabetic of these elements Bi, Cd, In, Pb, Sn, Tl, Zn are as follows:

Considering the binary systems between alkali metals: Li only has appreciable solubility in pair

The other three alkali metals:

practically do not dissolve Li even when liquid and therefore their melting points are not lowered by presence of Li Na is in liquid phase miscible with all three heavier alkali metals, but on freezing forms intermetallic compounds and eutectics:

The 3 binary systems between the three heavier alkali metals are all miscible in solid at melting point, but all form poor solid solutions that have melting point minima. This is distinct from eutectic: at eutectic point, two solid phases coexist, and close to eutectic point, the liquidus temperature rises rapidly as just one separates, whereas at poor solid solution melting point minimum, there is a single solid phase, and away from the minimum the liquidus temperature rises only slowly.

See also

References

<templatestyles src="Reflist/styles.css" />

  1. ↑ Wikisource One or more of the preceding sentences incorporates text from a publication now in the public domain: Script error: No such module "template wrapper".
  2. ↑ Script error: No such module "citation/CS1".
  3. ↑ Oshe, R.W. (ed.), "Handbook of Thermodynamic and Transport Properties of Alkali Metals", Oxford. UK, Blackwell Scientific Publications Ltd, 1985, p. 987
  4. ↑ a b c d e Script error: No such module "citation/CS1".
  5. ↑ Johnson Manufacturing Co, MSDS for Chip Quik Alloy w/Lead. Retrieved on February 6, 2015.
  6. ↑ Script error: No such module "citation/CS1".
  7. ↑ a b c Script error: No such module "citation/CS1".
  8. ↑ Script error: No such module "citation/CS1".
  9. ↑ Script error: No such module "Citation/CS1".
  10. ↑ a b Script error: No such module "citation/CS1".Script error: No such module "Unsubst".
  11. ↑ a b Script error: No such module "citation/CS1".
  12. ↑ Script error: No such module "citation/CS1".
  13. ↑ Script error: No such module "citation/CS1".
  14. ↑ Script error: No such module "citation/CS1".
  15. ↑ Script error: No such module "citation/CS1".
  16. ↑ Script error: No such module "Citation/CS1".
  17. ↑ msl747.PDF. (PDF). Retrieved 2010-07-06.
  18. ↑ Script error: No such module "citation/CS1".
  19. ↑ Script error: No such module "citation/CS1".
  20. ↑ Script error: No such module "citation/CS1".
  21. ↑ Script error: No such module "citation/CS1".

Script error: No such module "Check for unknown parameters".

Further reading

  • Script error: No such module "citation/CS1".
  • Weast, R.C., "CRC Handbook of Chemistry and Physics", 55th ed, CRC Press, Cleveland, 1974, p. F-22

External links

Retrieved from "http://debianws.lexgopc.com/wiki143/index.php?title=Fusible_alloy&oldid=1312509"