Board foot
Template:Short description Template:Infobox Unit The board foot or board-foot is a unit of measurement for the volume of lumber in the United States and Canada.[1] It equals the volume of a board that is Script error: No such module "convert". in length, one foot in width, and Script error: No such module "convert". in thickness, or exactly Script error: No such module "val". liters. Board foot can be abbreviated as FBM (for "foot, board measure"), BDFT, or BF. A thousand board feet can be abbreviated as MFBM, MBFT, or MBF. Similarly, a million board feet can be abbreviated as MMFBM, MMBFT, or MMBF.
Until the 1970s, in Australia and New Zealand, the terms super foot and superficial foot were used with the same meaning.[2][3][4]
Description
One board foot equals:
- 1 ft × 1 ft × 1 in
- 12 in × 12 in × 1 in
- 12 ft × 1 in × 1 in
- 144 in3
- <templatestyles src="Fraction/styles.css" />1⁄12 ft3
- ≈ Script error: No such module "convert".
- ≈ Script error: No such module "convert".
- ≈ Script error: No such module "convert". or steres
- <templatestyles src="Fraction/styles.css" />1⁄1980 Petrograd Standard of board
Usage
The board foot is used to measure both rough (unprocessed) lumber and planed (surfaced) lumber. Rough lumber is measured before drying and planing, using its full sawn dimensions. Planed lumber, such as standard softwood "two by four" boards sold at retail, is measured using nominal dimensions—typically Script error: No such module "convert".—even though the actual size is only about Script error: No such module "convert". after processing. Despite the reduction in size due to drying and planing, nominal dimensions are still used when calculating board feet for surfaced softwood lumber. This convention simplifies pricing and standardization but may result in board footage values that do not reflect the true volume of wood in the final product. Essentially, the nominal dimensions assume a larger volume than the actual board contains, which is especially relevant when estimating material needs or costs. [5] For planed lumber, board footage is calculated using the nominal width and thickness, and the actual length of the board. This reflects the lumber’s original rough size before drying and surfacing. For rough lumber, board footage is calculated using the actual width, thickness, and length of the board.
See dimensional lumber for a full explanation of nominal versus actual dimensions. Briefly, for softwoods:
- Subtract Script error: No such module "convert". from nominal sizes under 2 inches,
- Subtract Script error: No such module "convert". from nominal sizes between 2 and 8 inches,
- Subtract Script error: No such module "convert". for nominal sizes over 8 inches.[6]
The system is less complex for hardwoods, because actual board measurements are used.
Board feet can also be used a measure for the volume of logs, namely the estimated total volume of lumber that will result once a sawlog is processed on a sawmill. A variety of formulas and tables, for instance the Doyle Log Rule, exist to calculate this for a log based on its diameter and length, taking into account taper, saw kerf, and waste from cutting. [7]
See also
<templatestyles src="Div col/styles.css"/>
References
<templatestyles src="Reflist/styles.css" />
- ↑ Board foot
- ↑ Script error: No such module "citation/CS1".
- ↑ Script error: No such module "citation/CS1". Template:Webarchive
- ↑ Script error: No such module "citation/CS1". Template:Webarchive
- ↑ Script error: No such module "citation/CS1".
- ↑ Script error: No such module "citation/CS1".
- ↑ Script error: No such module "citation/CS1".
Script error: No such module "Check for unknown parameters".
External links
Script error: No such module "Navbox". Template:United States Customary Units