Operational amplifier: Difference between revisions

Latest revision as of 01:11, 18 November 2025

An operational amplifier (often op amp or opamp) is a DC-coupled electronic amplifier with a differential input, a (usually) single-ended output voltage,^[1] and an extremely high gain. Its name comes from its original use of performing mathematical operations in analog computers. The voltage-feedback opamp (the focus of this article) amplifies the voltage difference between its two inputs, while the less common current-feedback op amp amplifes the current between its two inputs.^[2]

By using negative feedback, an op amp circuit's characteristics (e.g. its gain, input and output impedance, bandwidth, and functionality) can be determined by external components and have little dependence on temperature coefficients or engineering tolerance in the op amp itself. This flexibility has made the op amp a popular building block in analog circuits.

Today, op amps are used widely in consumer, industrial, and scientific electronics. Many standard integrated circuit op amps cost only a few cents; however, some integrated or hybrid operational amplifiers with special performance specifications may cost over Template:Currency.^[3] Op amps may be packaged as components or used as elements of more complex integrated circuits.

The op amp is one type of differential amplifier. Other differential amplifier types include the fully differential amplifier (an op amp with a differential rather than single-ended output), the instrumentation amplifier (usually built from three op amps), the isolation amplifier (with galvanic isolation between input and output), and negative-feedback amplifier (usually built from one or more op amps and a resistive feedback network).

Operation

File:Op-amp open-loop 1.svg

An op amp without negative feedback (a comparator)

The amplifier's differential inputs consist of a non-inverting input (+) with voltage Template:Math and an inverting input (−) with voltage Template:Math; ideally the op amp amplifies only the difference in voltage between the two, which is called the differential input voltage. The output voltage of the op amp Template:Math is given by the equation $V_{out} = A_{OL} (V_{+} - V_{-}),$ where Template:Math is the open-loop gain of the amplifier (the term "open-loop" refers to the absence of an external feedback loop from the output to the input).

Open-loop amplifier

The magnitude of Template:Math is typically very large (100,000 or more for integrated circuit op amps, corresponding to +100 dB). Thus, even small microvolts of difference between Template:Math and Template:Math may drive the amplifier into clipping or saturation. The magnitude of Template:Math is not well controlled by the manufacturing process, and so it is impractical to use an open-loop amplifier as a stand-alone differential amplifier.

Without negative feedback, and optionally positive feedback for regeneration, an open-loop op amp acts as a comparator, although comparator ICs are better suited.^[4] If the inverting input of an ideal op amp is held at ground (0 V), and the input voltage Template:Math applied to the non-inverting input is positive, the output will be maximum positive; if Template:Math is negative, the output will be maximum negative.

Closed-loop amplifier

File:Operational amplifier noninverting.svg

An op amp with negative feedback (a non-inverting amplifier)

If predictable operation is desired, negative feedback is used, by applying a portion of the output voltage to the inverting input. The closed-loop feedback greatly reduces the gain of the circuit. When negative feedback is used, the circuit's overall gain and response is determined primarily by the feedback network, rather than by the op-amp characteristics. If the feedback network is made of components with values small relative to the op amp's input impedance, the value of the op amp's open-loop response Template:Math does not seriously affect the circuit's performance. In this context, high input impedance at the input terminals and low output impedance at the output terminal(s) are particularly useful features of an op amp.

The response of the op-amp circuit with its input, output, and feedback circuits to an input is characterized mathematically by a transfer function; designing an op-amp circuit to have a desired transfer function is in the realm of electrical engineering. The transfer functions are important in most applications of op amps, such as in analog computers.

In the non-inverting amplifier on the right, the presence of negative feedback via the voltage divider Template:Math, Template:Math determines the closed-loop gain Template:Math. Equilibrium will be established when Template:Math is just sufficient to pull the inverting input to the same voltage as Template:Math. The voltage gain of the entire circuit is thus Template:Math. As a simple example, if Template:Math and Template:Math, Template:Math will be 2 V, exactly the amount required to keep Template:Math at 1 V. Because of the feedback provided by the Template:Math, Template:Math network, this is a closed-loop circuit.

Another way to analyze this circuit proceeds by making the following (usually valid) assumptions:^[5]

When an op amp operates in linear (i.e., not saturated) mode, the difference in voltage between the non-inverting (+) and inverting (−) pins is negligibly small.
The input impedance of the (+) and (−) pins is much larger than other resistances in the circuit.

The input signal Template:Math appears at both (+) and (−) pins per assumption 1, resulting in a current Template:Mvar through Template:Math equal to Template:Math: $i = \frac{V_{in}}{R_{g}} .$

Because Kirchhoff's current law states that the same current must leave a node as enter it, and because the impedance into the (−) pin is near infinity per assumption 2, we can assume practically all of the same current Template:Mvar flows through Template:Math, creating an output voltage $V_{out} = V_{in} + i R_{f} = V_{in} + (\frac{V_{in}}{R_{g}} R_{f}) = V_{in} + \frac{V_{in} R_{f}}{R_{g}} = V_{in} (1 + \frac{R_{f}}{R_{g}}) .$

By combining terms, we determine the closed-loop gain Template:Math: $A_{CL} = \frac{V_{out}}{V_{in}} = 1 + \frac{R_{f}}{R_{g}} .$

Characteristics Script error: No such module "anchor".

Ideal op amps

File:Op-Amp Internal.svg

An equivalent circuit of an operational amplifier that models some resistive non-ideal parameters.

An ideal op amp is usually considered to have the following characteristics:^[6]^[7]^[8]

Infinite open-loop gain Template:Math
Infinite input impedance Template:Math, and so zero input current
Zero input offset voltage
Infinite output voltage range
Infinite bandwidth with zero phase shift and infinite slew rate
Zero output impedance Template:Math, and so infinite output current range
Zero noise
Infinite common-mode rejection ratio (CMRR)
Infinite power supply rejection ratio.

These ideals can be summarized by the two Template:Em:

In a closed loop the output does whatever is necessary to make the voltage difference between the inputs zero.
The inputs draw zero current.^[9]Template:Rp

The first rule only applies in the usual case where the op amp is used in a closed-loop design (negative feedback, where there is a signal path of some sort feeding back from the output to the inverting input). These rules are commonly used as a good first approximation for analyzing or designing op-amp circuits.^[9]Template:Rp

None of these ideals can be perfectly realized. A real op amp may be modeled with non-infinite or non-zero parameters using equivalent resistors and capacitors in the op-amp model. The designer can then include these effects into the overall performance of the final circuit. Some parameters may turn out to have negligible effect on the final design while others represent actual limitations of the final performance.

Real op amps

Real op amps differ from the ideal model in various aspects.

Template:Glossary begin Template:Term Template:Defn

Template:Term Template:Defn

Template:Term Template:Defn Template:Glossary end

Non-linear imperfections

File:Inverting Amplifier Signal Clipping.png

The input (yellow) and output (green) of a saturated op amp in an inverting amplifier

Template:Glossary begin Template:Term Template:Defn

Template:Term Template:Defn

Template:Term Template:Defn Template:Glossary end

Power considerations

Template:Glossary begin Template:Term Template:Defn

Template:Term Template:Defn

Template:Term Template:Defn Template:Glossary end

Classification

File:LH033CG.jpg

LH0033CG: a high speed hybrid IC op amp

Op amps may be classified by their construction:

discrete, built from individual transistors or tubes/valves,
hybrid, consisting of discrete and integrated components,
full integrated circuits — most common, having displaced the former two due to low cost.

IC op amps may be classified in many ways, including:

Device grade, including acceptable operating temperature ranges and other environmental or quality factors. For example: LM101, LM201, and LM301 refer to the military, industrial, and commercial versions of the same component. Military and industrial-grade components offer better performance in harsh conditions than their commercial counterparts but are sold at higher prices.
Classification by package type may also affect environmental hardiness, as well as manufacturing options; DIP, and other through-hole packages are tending to be replaced by surface-mount devices.
Classification by internal compensation: op amps may suffer from high frequency instability in some negative feedback circuits unless a small compensation capacitor modifies the phase and frequency responses. Op amps with a built-in capacitor are termed compensated, and allow circuits above some specified closed-loop gain to be stable with no external capacitor. In particular, op amps that are stable even with a closed loop gain of 1 are called unity gain compensated.
Single, dual and quad versions of many commercial op-amp IC are available, meaning 1, 2 or 4 operational amplifiers are included in the same package.
Rail-to-rail input (and/or output) op amps can work with input (and/or output) signals very close to the power supply rails.^[10]
CMOS op amps (such as the CA3140E) provide extremely high input resistances, higher than JFET-input op amps, which are normally higher than bipolar-input op amps.
Programmable op amps allow the quiescent current, bandwidth and so on to be adjusted by an external resistor.
Manufacturers often market their op amps according to purpose, such as low-noise pre-amplifiers, wide bandwidth amplifiers, and so on.

Applications

Script error: No such module "Labelled list hatnote".

Historical timeline

File:K2-w Vacuum Tube Op-amp.jpg

GAP/R K2-W: a vacuum-tube op amp (1953)

1941: A vacuum tube op amp. An op amp, defined as a general-purpose, DC-coupled, high-gain, inverting feedback amplifier, is first found in U.S. patent 2,401,779 "Summing Amplifier" filed by Karl D. Swartzel Jr. of Bell Labs in 1941. This design used three vacuum tubes to achieve a gain of 90 dB and operated on voltage rails of ±350 V. It had a single inverting input rather than differential inverting and non-inverting inputs, as are common in today's op amps. Throughout World War II, Swartzel's design proved its value by being liberally used in the M9 artillery director designed at Bell Labs. This artillery director worked with the SCR-584 radar system to achieve extraordinary hit rates (near 90%) that would not have been possible otherwise.^[11]

1947: An op amp with an explicit non-inverting input. In 1947, the operational amplifier was first formally defined and named in a paper by John R. Ragazzini of Columbia University.^[12] In this same paper a footnote mentioned an op-amp design by a student that would turn out to be quite significant. This op amp, designed by Loebe Julie, had two major innovations. Its input stage used a long-tailed triode pair with loads matched to reduce drift in the output and, far more importantly, it was the first op-amp design to have two inputs (one inverting, the other non-inverting). The differential input made a whole range of new functionality possible, but it would not be used for a long time due to the rise of the chopper-stabilized amplifier.^[11]

1949: A chopper-stabilized op amp. In 1949, Edwin A. Goldberg designed a chopper-stabilized op amp.^[13] This set-up uses a normal op amp with an additional AC amplifier that goes alongside the op amp. The chopper gets an AC signal from DC by switching between the DC voltage and ground at a fast rate (60 or 400 Hz). This signal is then amplified, rectified, filtered and fed into the op amp's non-inverting input. This vastly improved the gain of the op amp while significantly reducing the output drift and DC offset. Unfortunately, any design that used a chopper couldn't use the non-inverting input for any other purpose. Nevertheless, the much-improved characteristics of the chopper-stabilized op amp made it the dominant way to use op amps. Techniques that used the non-inverting input were not widely practiced until the 1960s when op-amp ICs became available.

1953: A commercially available op amp. In 1953, vacuum tube op amps became commercially available with the release of the model K2-W from George A. Philbrick Researches, Incorporated. The designation on the devices shown, GAP/R, is an acronym for the complete company name. Two nine-pin 12AX7 vacuum tubes were mounted in an octal package and had a model K2-P chopper add-on available. This op amp was based on a descendant of Loebe Julie's 1947 design and, along with its successors, would start the widespread use of op amps in industry.^[14]

File:Discrete opamp.png

GAP/R model P45: a solid-state, discrete op amp (1961).

1961: A discrete IC op amp. With the birth of the transistor in 1947, and the silicon transistor in 1954, the concept of ICs became a reality. The introduction of the planar process in 1959 made transistors and ICs stable enough to be commercially useful. By 1961, solid-state, discrete op amps were being produced. These op amps were effectively small circuit boards with packages such as edge connectors. They usually had hand-selected resistors in order to improve things such as voltage offset and drift. The P45 (1961) had a gain of 94 dB and ran on ±15 V rails. It was intended to deal with signals in the range of ±10 V.

1961: A varactor bridge op amp. There have been many different directions taken in op-amp design. Varactor bridge op amps started to be produced in the early 1960s.^[15]^[16] They were designed to have extremely small input current and are still amongst the best op amps available in terms of common-mode rejection with the ability to correctly deal with hundreds of volts at their inputs.

File:Modular opamp.png

GAP/R model PP65: a solid-state op amp in a potted module (1962)

1962: An op amp in a potted module. By 1962, several companies were producing modular potted packages that could be plugged into printed circuit boards.Script error: No such module "Unsubst". These packages were crucially important as they made the operational amplifier into a single black box which could be easily treated as a component in a larger circuit.

1963: A monolithic IC op amp. In 1963, the first monolithic IC op amp, the μA702 designed by Bob Widlar at Fairchild Semiconductor, was released. Monolithic ICs consist of a single chip as opposed to a chip and discrete parts (a discrete IC) or multiple chips bonded and connected on a circuit board (a hybrid IC). Almost all modern op amps are monolithic ICs; however, this first IC did not meet with much success. Issues such as an uneven supply voltage, low gain and a small dynamic range held off the dominance of monolithic op amps until 1965 when the μA709^[17] (also designed by Bob Widlar) was released.

1968: Release of the μA741. The popularity of monolithic op amps was further improved with the release of the LM101 in 1967, which solved a variety of issues, and the subsequent release of the μA741 in 1968. The μA741 was extremely similar to the LM101 except that Fairchild's manufacturing processes allowed them to include a 30 pF compensation capacitor inside the chip instead of requiring external compensation. This simple difference has made the 741 a canonical op amp and a range of modern amps base their pinout on the 741s. The μA741 is still in production, and has become ubiquitous in electronics—many manufacturers produce a version of this classic chip, recognizable by part numbers containing 741.

1970: First high-speed, low-input current FET design. In the 1970s high-speed, low-input current designs started to be made by using FETs. These would be largely replaced by op amps made with MOSFETs in the 1980s.

1972: Single-sided supply op amps being produced. A single-sided supply op amp is one where the input and output voltages can be as low as the negative power supply voltage instead of needing to be at least two volts above it. The result is that it can operate in many applications with the negative supply pin on the op amp being connected to the signal ground, thus eliminating the need for a separate negative power supply. The LM324, released in 1972, was one such op amp that came in a quad package (four separate op amps in one package) and became an industry standard.

Recent trends. Supply voltages in analog circuits have decreased (as they have in digital logic) and low-voltage op amps have been introduced reflecting this. Supplies of 5 V and increasingly 3.3 V (sometimes as low as 1.8 V) are common. To maximize the signal range, modern op amps commonly have rail-to-rail output (the output signal can range from the lowest supply voltage to the highest) and sometimes rail-to-rail inputs.^[10]

Notes

Template:Reflist

References

Template:Reflist

External links

Template:Sister project Template:Sister project Template:Sister project

Op Amp Circuit Collection- National Semiconductor Corporation
Operational Amplifiers - Chapter on All About Circuits
Loop Gain and its Effects on Analog Circuit Performance - Introduction to loop gain, gain and phase margin, loop stability
Simple Op Amp Measurements Template:Webarchive How to measure offset voltage, offset and bias current, gain, CMRR, and PSRR.
Operational Amplifiers. Introductory on-line text by E. J. Mastascusa (Bucknell University).
Introduction to op-amp circuit stages, second order filters, single op-amp bandpass filters, and a simple intercom
MOS op amp design: A tutorial overview
Operational Amplifier Noise Prediction (All Op Amps) using spot noise
Operational Amplifier Basics Template:Webarchive
History of the Op-amp Template:Webarchive, from vacuum tubes to about 2002
Loebe Julie historical OpAmp interview by Bob Pease
www.PhilbrickArchive.org Template:Spaced ndashA free repository of materials from George A Philbrick / Researches - Operational Amplifier Pioneer
What's The Difference Between Operational Amplifiers And Instrumentation Amplifiers? Template:Webarchive, Electronic Design Magazine

Template:Authority control

↑ Script error: No such module "citation/CS1".
↑ Script error: No such module "citation/CS1".
↑ Script error: No such module "citation/CS1".
↑ Script error: No such module "citation/CS1".
↑ Script error: No such module "citation/CS1".
↑ Script error: No such module "citation/CS1".
↑ Script error: No such module "citation/CS1".
↑ Script error: No such module "citation/CS1".
↑ ^a ^b Script error: No such module "citation/CS1".
↑ ^a ^b Cite error: Invalid <ref> tag; no text was provided for refs named rail-to-rail
↑ ^a ^b Script error: No such module "citation/CS1".
↑ Script error: No such module "Citation/CS1".
↑ Script error: No such module "citation/CS1".
↑ Script error: No such module "citation/CS1".
↑ Script error: No such module "citation/CS1".
↑ June 1961 advertisement for Philbrick P2, Script error: No such module "citation/CS1".
↑ Script error: No such module "citation/CS1".

[1] Script error: No such module "citation/CS1".

[2] Script error: No such module "citation/CS1".

[3] Script error: No such module "citation/CS1".

[4] Script error: No such module "citation/CS1".

[5] Script error: No such module "citation/CS1".

[6] Script error: No such module "citation/CS1".

[7] Script error: No such module "citation/CS1".

[8] Script error: No such module "citation/CS1".

[AoE-9] Script error: No such module "citation/CS1".

[rail-to-rail-10] Cite error: Invalid <ref> tag; no text was provided for refs named rail-to-rail

[Jung-2004-11] Script error: No such module "citation/CS1".

[12] Script error: No such module "Citation/CS1".

[13] Script error: No such module "citation/CS1".

[14] Script error: No such module "citation/CS1".

[15] Script error: No such module "citation/CS1".

[16] June 1961 advertisement for Philbrick P2, Script error: No such module "citation/CS1".

[17] Script error: No such module "citation/CS1".

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

[11]

[12]

[13]

[14]

[15]

[16]

[17]

Operational amplifier: Difference between revisions

Latest revision as of 01:11, 18 November 2025

Contents

Operation

Open-loop amplifier

Closed-loop amplifier

Characteristics Script error: No such module "anchor".

Ideal op amps

Real op amps

Non-linear imperfections

Power considerations

Classification

Applications

Historical timeline

See also

Notes

References

Further reading

External links

Navigation menu

@@ Line 4: / Line 4: @@
 | name = Operational amplifier
 | image = Ua741 opamp.jpg
-| caption = The μA741, a popular early integrated op amp
+| caption = The [[741_(operational_amplifier)|μA741]], a popular early integrated op amp
 | type = [[Discrete circuit]]<br/>[[Integrated circuit]]
 | working_principle =
@@ Line 18: / Line 18: @@
 }}
-An '''operational amplifier''' (often '''op amp''' or '''opamp''') is a [[direct coupling|DC-coupled]] [[Electronic component|electronic]] [[voltage]] [[amplifier]] with a [[differential input]], a (usually) [[Single-ended signaling|single-ended]] output,<ref>{{cite web |url=http://www.maxim-ic.com/appnotes.cfm/an_pk/1108 |id=Maxim Application Note 1108 |title=Understanding Single-Ended, Pseudo-Differential and {{Sic|hide=y|Fully|-}}Differential ADC Inputs |archive-url=https://web.archive.org/web/20070626153413/http://www.maxim-ic.com/appnotes.cfm/an_pk/1108 |archive-date=2007-06-26 |access-date=November 10, 2007}}</ref> and an extremely high [[gain (electronics)|gain]]. Its name comes from its original use of performing [[mathematical operations]] in [[analog computers]].
+An '''operational amplifier''' (often '''op amp''' or '''opamp''') is a [[direct coupling|DC-coupled]] [[Electronic component|electronic]] [[amplifier]] with a [[differential input]], a (usually) [[Single-ended signaling|single-ended]] output [[voltage]],<ref>{{cite web |url=http://www.maxim-ic.com/appnotes.cfm/an_pk/1108 |id=Maxim Application Note 1108 |title=Understanding Single-Ended, Pseudo-Differential and {{Sic|hide=y|Fully|-}}Differential ADC Inputs |archive-url=https://web.archive.org/web/20070626153413/http://www.maxim-ic.com/appnotes.cfm/an_pk/1108 |archive-date=2007-06-26 |access-date=November 10, 2007}}</ref> and an extremely high [[gain (electronics)|gain]]. Its name comes from its original use of performing [[mathematical operations]] in [[analog computer]]s. The voltage-feedback opamp (the focus of this article) amplifies the voltage difference between its two inputs, while the less common [[Current-feedback operational amplifier|current-feedback op amp]] amplifes the current between its two inputs.<ref>{{Cite web |last=Karki |first=James |date=November 1998 |title=Voltage Feedback Vs Current Feedback Op Amps |url=https://www.ti.com/lit/an/slva051/slva051.pdf |website=[[Texas Instruments]]}}</ref>
 By using [[negative feedback]], an [[Op amp circuits|op amp circuit]]'s characteristics (e.g. its gain, input and [[output impedance]], [[bandwidth (signal processing)|bandwidth]], and functionality) can be determined by external components and have little dependence on [[temperature coefficient]]s or [[engineering tolerance]] in the op amp itself. This flexibility has made the op amp a popular building block in [[analog circuit]]s.
@@ Line 42: / Line 42: @@
 If predictable operation is desired, negative feedback is used, by applying a portion of the output voltage to the inverting input. The ''closed-loop'' feedback greatly reduces the gain of the circuit. When negative feedback is used, the circuit's overall gain and response is determined primarily by the feedback network, rather than by the op-amp characteristics. If the feedback network is made of components with values small relative to the op amp's input impedance, the value of the op amp's open-loop response {{math|''A''<sub>OL</sub>}} does not seriously affect the circuit's performance. In this context, high input [[Electrical impedance|impedance]] at the input terminals and low output impedance at the output terminal(s) are particularly useful features of an op amp.
-The response of the op-amp circuit with its input, output, and feedback circuits to an input is characterized mathematically by a [[transfer function]]; designing an op-amp circuit to have a desired transfer function is in the realm of [[electrical engineering]]. The transfer functions are important in most applications of op amps, such as in [[analog computers]].
+The response of the op-amp circuit with its input, output, and feedback circuits to an input is characterized mathematically by a [[transfer function]]; designing an op-amp circuit to have a desired transfer function is in the realm of [[electrical engineering]]. The transfer functions are important in most applications of op amps, such as in [[analog computer]]s.
 In the non-inverting amplifier on the right, the presence of negative feedback via the [[voltage divider]] {{math|''R''<sub>f</sub>}}, {{math|''R''<sub>g</sub>}} determines the ''closed-loop gain'' {{math|1= ''A''<sub>CL</sub> = ''V''<sub>out</sub> / ''V''<sub>in</sub>}}. Equilibrium will be established when {{math|''V''<sub>out</sub>}} is just sufficient to pull the inverting input to the same voltage as {{math|''V''<sub>in</sub>}}. The voltage gain of the entire circuit is thus {{math|1 + ''R''<sub>f</sub> / ''R''<sub>g</sub>}}. As a simple example, if {{math|1= ''V''<sub>in</sub> = 1 V}} and {{math|1= R<sub>f</sub> = ''R''<sub>g</sub>}}, {{math|''V''<sub>out</sub>}} will be 2&nbsp;V, exactly the amount required to keep {{math|''V''<sub>&minus;</sub>}} at 1&nbsp;V. Because of the feedback provided by the {{math|''R''<sub>f</sub>}}, {{math|''R''<sub>g</sub>}} network, this is a ''closed-loop'' circuit.
@@ Line 59: / Line 59: @@
 <math display="block">A_\text{CL} = \frac{V_\text{out}}{V_\text{in}} = 1 + \frac{R_\text{f}}{R_\text{g}}.</math>
-==Op-amp characteristics==
+==Characteristics {{anchor|Op-amp characteristics}}==
 <!-- [[Ideal and real op-amps]] redirects here, to "Op-amp characteristics" -->
 === Ideal op amps ===
@@ Line 121: / Line 121: @@
 {{term| Finite [[bandwidth (signal processing)|bandwidth]] }}
-{{defn| All amplifiers have finite bandwidth. To a first approximation, the op amp has the frequency response of an [[integrator]] with gain. That is, the gain of a typical op amp is inversely proportional to frequency and is characterized by its [[gain–bandwidth product]] (GBWP). For example, an op amp with a {{abbr|GBWP|gain–bandwith product}} of 1&nbsp;MHz would have a gain of 5 at 200&nbsp;kHz, and a gain of 1 at 1&nbsp;MHz. This dynamic response coupled with the very high DC gain of the op amp gives it the characteristics of a first-order [[low-pass filter]] with very high DC gain and low cutoff frequency given by the {{abbr|GBWP|gain–bandwith product}} divided by the DC gain.
+{{defn| All amplifiers have finite bandwidth. To a first approximation, the op amp has the frequency response of an [[integrator]] with gain. That is, the gain of a typical op amp is inversely proportional to frequency and is characterized by its [[gain–bandwidth product]] (GBWP). For example, an op amp with a {{abbr|GBWP|gain–bandwidth product}} of 1&nbsp;[[megahertz]]&nbsp;(MHz) would have a gain of 5 at 200&nbsp;kilohertz, and a gain of 1 at 1&nbsp;MHz. This dynamic response coupled with the very high DC gain of the op amp gives it the characteristics of a first-order [[low-pass filter]] with very high DC gain and low cutoff frequency given by the {{abbr|GBWP|gain–bandwidth product}} divided by the DC gain.
 The finite bandwidth of an op amp can be the source of several problems, including:
@@ Line 132: / Line 132: @@
 {{glossary end}}
-Typical low-cost, general-purpose op amps exhibit a {{abbr|GBWP|gain–bandwith product}} of a few megahertz. Specialty and high-speed op amps exist that can achieve a {{abbr|GBWP|gain–bandwith product}} of hundreds of megahertz. For very high-frequency circuits, a [[current-feedback operational amplifier]] is often used. }}
+''Fast'' or ''high-speed'' is used to refer to op amps with at least 50&nbsp;MHz of {{abbr|GBWP|gain–bandwidth product}} and a high slew rate.<ref>{{Cite web |last=Liska |first=Peggy |date=July 2020 |title=3 Common Questions When Designing with High-speed Amplifiers |url=https://www.ti.com/lit/ta/sszt273/sszt273.pdf |website=[[Texas Instruments]]}}</ref><ref>{{Cite web |last=Jung |first=Walt |last2=Kester |first2=Walt |title=High Speed Op Amps |url=https://www.analog.com/media/en/training-seminars/design-handbooks/Practical-Analog-Design-Techniques/Section2.pdf |website=[[Analog Devices]]}}</ref> While typical low-cost, general-purpose op amps exhibit a {{abbr|GBWP|gain–bandwidth product}} of a few megahertz, specialty and high-speed op amps exist that can achieve a {{abbr|GBWP|gain–bandwidth product}} of hundreds of megahertz. Very high-frequency circuits often use a [[current-feedback operational amplifier]], because their bandwidth doesn't decrease with gain like voltage-feedback op amps.}}
 {{term| Noise }}
 {{defn| Amplifiers intrinsically output noise, even when there is no signal applied. This can be due to internal thermal noise and flicker noise of the device. For applications with high gain or high bandwidth, noise becomes an important consideration and a [[low-noise amplifier]], which is specifically designed for minimum intrinsic noise, may be required to meet performance requirements. }}
 {{glossary end}}
 ====Non-linear imperfections====
@@ Line 197: / Line 196: @@
 Modern integrated [[FET]] or [[MOSFET]] op amps approximate more closely the ideal op amp than bipolar ICs when it comes to input impedance and input bias currents. Bipolars are generally better when it comes to input ''voltage'' offset, and often have lower noise. Generally, at room temperature, with a fairly large signal, and limited bandwidth, FET and MOSFET op amps now offer better performance. }}
 {{glossary end}}
-== Internal circuitry of 741-type op amp<span class="anchor" id="741"></span> ==
-[[Image:OpAmpTransistorLevel Colored Labeled.svg|thumb|right|500px|A component-level diagram of the common 741 op amp. Dotted lines outline: {{colorbox|red}}{{nbsp}}[[current mirror]]s; {{colorbox|blue}}{{nbsp}}[[differential amplifier]]; {{colorbox|magenta}}{{nbsp}}[[Class-A amplifier|class A]] gain stage; {{colorbox|limegreen}}{{nbsp}}voltage level shifter; {{colorbox|cyan}}{{nbsp}}output stage.]]
-Sourced by many manufacturers, and in multiple similar products, an example of a bipolar transistor operational amplifier is the 741 integrated circuit designed in 1968 by David Fullagar at [[Fairchild Semiconductor]] after [[Bob Widlar]]'s LM301 integrated circuit design.<ref name="Lee">{{cite web
- |last         = Lee
- |first        = Thomas H.
- |url          = http://www.stanford.edu/class/archive/ee/ee214/ee214.1032/Handouts/ho18opamp.pdf
- |title        = IC Op-Amps Through the Ages
- |date         = November 18, 2002
- |publisher    = Stanford University
- |id           = Handout #18
- |series       = EE214 Fall 2002 Course Notes
- |url-status   = dead
- |archive-url  = https://web.archive.org/web/20121024123401/http://www.stanford.edu/class/archive/ee/ee214/ee214.1032/Handouts/ho18opamp.pdf
- |archive-date = October 24, 2012
- |access-date  = July 5, 2011
- }}</ref>
-In this discussion, we use the parameters of the [[hybrid-pi model]] to characterize the small-signal, grounded emitter characteristics of a transistor. In this model, the current gain of a transistor is denoted
-{{math|''h''<sub>fe</sub>}}, more commonly denoted {{mvar|β}}.<ref name="Lu">{{cite web
- |url          = http://cc.ee.ntu.edu.tw/~lhlu/eecourses/Electronics2/Electronics_Ch10.pdf
- |title        = Electronics 2, Chapter 10
- |last1        = Lu
- |first1       = Liang-Hung
- |publisher    = National Taiwan University, Graduate Institute of Electronics Engineering
- |access-date  = 2014-02-22
- |url-status   = dead
- |archive-url  = https://web.archive.org/web/20140630021239/http://cc.ee.ntu.edu.tw/~lhlu/eecourses/Electronics2/Electronics_Ch10.pdf
- |archive-date = 2014-06-30
- }}</ref>
-=== Architecture ===
-A small-scale [[integrated circuit]], the 741 op amp shares with most op amps an internal structure consisting of three gain stages:<ref>{{cite web |url=http://www.righto.com/2015/10/inside-ubiquitous-741-op-amp-circuits.html |title=Understanding silicon circuits: inside the ubiquitous 741 op amp |website=www.righto.com |access-date=28 April 2018 |url-status=live |archive-url=https://web.archive.org/web/20171009072728/http://www.righto.com/2015/10/inside-ubiquitous-741-op-amp-circuits.html |archive-date=9 October 2017 }}</ref>
-# [[Differential amplifier]] (outlined dark blue) — provides high differential amplification (gain), with rejection of [[common-mode signal]], low noise, high [[input impedance]], and drives a
-# Voltage amplifier (outlined [[magenta]]) — provides high voltage gain, a single-pole frequency [[roll-off]], and in turn drives the
-# Output amplifier (outlined [[cyan]] and [[green]]) — provides high current gain (low [[output impedance]]), along with output current limiting, and output short-circuit protection.
-Additionally, it contains [[current mirror]] (outlined red) bias circuitry and [[Frequency compensation|compensation]] capacitor ({{val|30|u=pF}}).
-==== Differential amplifier ====
-The input stage consists of a cascaded [[differential amplifier]] (outlined in dark blue) followed by a current-mirror [[active load]]. This constitutes a [[transconductance amplifier]], turning a differential voltage signal at the bases of Q1, Q2 into a current signal into the base of Q15.
-It entails two cascaded transistor pairs, satisfying conflicting requirements. The first stage consists of the matched NPN [[emitter follower]] pair Q1, Q2 that provide high input impedance. The second is the matched PNP [[common-base]] pair Q3, Q4 that eliminates the undesirable [[Miller effect]]; it drives an [[active load]] Q7 plus matched pair Q5, Q6.
-That active load is implemented as a modified [[Wilson current mirror]]; its role is to convert the (differential) input current signal to a single-ended signal without the attendant 50% losses (increasing the op amp's open-loop gain by {{val|3|u=[[decibel|dB]]}}).<ref group="nb">Widlar used this same trick in μA702 and μA709</ref> Thus, a small-signal differential current in Q3 versus Q4 appears summed (doubled) at the base of Q15, the input of the voltage gain stage.
-==== Voltage amplifier ====
-The (class-A) voltage gain stage (outlined in [[magenta]]) consists of the two NPN transistors Q15 and Q19 connected in a [[Darlington transistor|Darlington configuration]] and uses the output side of current mirror formed by Q12 and Q13 as its collector (dynamic) load to achieve its high voltage gain. The output sink transistor Q20 receives its base drive from the common collectors of Q15 and Q19; the level-shifter Q16 provides base drive for the output source transistor Q14.<!-- Note the similarity between the transistors Q15 and Q7 -- just accidentally a similar position in the plan, not a matched pair--> The transistor Q22 prevents this stage from delivering excessive current to Q20 and thus limits the output sink current.
-==== Output amplifier ====
-The output stage (Q14, Q20, outlined in cyan) is a [[Class AB]] amplifier. It provides an output drive with impedance of about {{val|50|u=Ω}}, in essence, current gain. Transistor Q16 (outlined in green) provides the quiescent current for the output transistors and Q17 limits output source current.
-=== Biasing circuits ===
-Biasing circuits provide appropriate quiescent current for each stage of the op amp.
-The {{val|39|u=kΩ}} resistor connecting the [[diode-connected transistor]]s  Q11 and Q12, and the given supply voltage {{math|1= ''V''{{sub|S}} = ''V''{{sub|S+}} − ''V''{{sub|S−}}}}, determine the current in the [[current mirror]]s, (matched pairs) Q10/Q11 and Q12/Q13. The collector current of Q11, {{math|1= ''i''{{sub|11}} × 39&nbsp;kΩ =}} {{math|''V''{{sub|S}} − 2''V''{{sub|BE}}}}. For the typical {{math|1= ''V''{{sub|S}} = {{val|20|u=V}}}}, the standing current in Q11 and Q12 (as well as in Q13) would be about {{val|1|u=mA}}. A supply current for a typical 741 of about {{val|2|u=mA}} agrees with the notion that these two bias currents dominate the quiescent supply current.<ref name="NS LM741" />
-Transistors Q11 and Q10 form a [[Widlar current mirror]], with quiescent current in Q10 {{math|''i''{{sub|10}}}} such that {{math|1= ln(''i''{{sub|11}}/''i''{{sub|10}}) = ''i''{{sub|10}} × {{val|5|u=kΩ}} / {{val|28|u=mV}}}}, where {{val|5|u=kΩ}} represents the emitter resistor of Q10, and {{val|28|u=mV}} is {{math|''V''{{sub|T}}}}, the [[thermal voltage]] at room temperature. In this case {{math|1= ''i''{{sub|10}} ≈ {{val|20|u=μA}}}}.
-==== Differential amplifier ====
-The biasing circuit of this stage is set by a feedback loop that forces the collector currents of Q10 and Q9 to (nearly) match. Any small difference in these currents provides drive for the common base of Q3 and Q4.<ref group="nb">The base drive for input transistors Q1/Q2 is the input bias current and must be sourced externally.</ref> The summed quiescent currents through Q1 and Q3 plus Q2 and Q4 is mirrored from Q8 into Q9, where it is summed with the collector current in Q10, the result being applied to the bases of Q3 and Q4.
-The quiescent currents through Q1 and Q3 (also Q2 and Q4) {{math|''i''{{sub|1}}}} will thus be half of {{math|''i''{{sub|10}}}}, of order about {{val|10|u=μA}}. Input bias current for the base of Q1 (also Q2) will amount to {{math|''i''{{sub|1}}/''β''}}; typically around {{val|50|u=nA}},<ref name="NS LM741" /> implying a current gain {{math|1= ''h''{{sub|fe}} ≈ 200}} for Q1 (also Q2).
-This feedback circuit tends to draw the common base node of Q3/Q4 to a voltage {{math|1= ''V''{{sub|com}} − 2''V''{{sub|BE}}}}, where {{math|''V''{{sub|com}}}} is the input common-mode voltage. At the same time, the magnitude of the quiescent current is relatively insensitive to the characteristics of the components Q1–Q4, such as {{math|''h''{{sub|fe}}}}, that would otherwise cause temperature dependence or part-to-part variations.
-Transistor Q7 drives Q5 and Q6 into conduction until their (equal) collector currents match that of Q1/Q3 and Q2/Q4. The quiescent current in Q7 is {{math|''V''{{sub|BE}} / {{val|50|u=kΩ}}}}, about {{val|35|u=μA}}, as is the quiescent current in Q15, with its matching operating point. Thus, the quiescent currents are pairwise matched in Q1/Q2, Q3/Q4, Q5/Q6, and Q7/Q15.
-==== Voltage amplifier ====
-Quiescent currents in Q16 and Q19 are set by the current mirror Q12/Q13, which is running at approximately {{val|1|u=mA}}. The collector current in Q19 tracks that standing current.{{elucidate|reason=Through what means?|date=October 2023}}
-==== Output amplifier ====
-In the circuit involving Q16 (variously named [[rubber diode]] or {{math|''V''{{sub|BE}}}} multiplier), the {{val|4.5|u=kΩ}} resistor must be conducting about {{val|100|u=μA}}, with Q16 {{math|1= ''V''{{sub|BE}} ≈ {{val|700|u=mV}}}}. Then {{math|''V''{{sub|CB}}}} must be about {{val|0.45|u=V}}, and {{math|1= ''V''{{sub|CE}} ≈ {{val|1.0|u=V}}}}. Because the Q16 collector is driven by a current source and the Q16 emitter drives into the Q19 collector current sink, the Q16 transistor establishes a voltage difference between the Q14 base and the Q20 base of about {{val|1|u=V}}, regardless of the common-mode voltage of Q14/Q20 bases. The standing current in Q14/Q20 will be a factor [[diode modelling|{{math|1= exp({{val|100|u=mV·mm}}/ ''V''{{sub|T}}) ≈ 36}}]] smaller than the {{val|1|u=mA}} quiescent current in the class A portion of the op amp. This (small) standing current in the output transistors establishes the output stage in class AB operation and reduces the [[crossover distortion]] of this stage.
-=== Small-signal differential mode ===
-A small differential input voltage signal gives rise, through multiple stages of current amplification, to a much larger voltage signal on output.
-==== Input impedance ====
-The input stage with Q1 and Q3 is similar to an emitter-coupled pair (long-tailed pair), with Q2 and Q4 adding some degenerating impedance. The input impedance is relatively high because of the small current through Q1–Q4. A typical 741 op amp has a differential input impedance of about {{val|2|u=MΩ}}.<ref name="NS LM741">National Semiconductor LM741 data sheet</ref> The common mode input impedance is even higher, as the input stage works at an essentially constant current.
-==== Differential amplifier ====
-A differential voltage {{math|''V''{{sub|in}}}} at the op amp inputs (pins 3 and 2, respectively) gives rise to a small differential current in the bases of Q1 and Q2 {{math|1= ''i''{{sub|in}} ≈ ''V''{{sub|in}} / (2''h''{{sub|ie}}''h''{{sub|fe}})}}. This differential base current causes a change in the differential collector current in each leg by {{math|''i''{{sub|in}}''h''{{sub|fe}}}}. Introducing the transconductance of Q1, {{math|1= ''g''{{sub|''m''}}''h''{{sub|fe}} / ''h''{{sub|ie}}}}, the (small-signal) current at the base of Q15 (the input of the voltage gain stage) is {{math|''V''{{sub|in}}''g''{{sub|''m''}} / 2}}.
-This portion of the op amp cleverly changes a differential signal at the op amp inputs to a single-ended signal at the base of Q15, and in a way that avoids wastefully discarding the signal in either leg. To see how, notice that a small negative change in voltage at the inverting input (Q2 base) drives it out of conduction, and this incremental decrease in current passes directly from Q4 collector to its emitter, resulting in a decrease in base drive for Q15. On the other hand, a small positive change in voltage at the non-inverting input (Q1 base) drives this transistor into conduction, reflected in an increase in current at the collector of Q3. This current drives Q7 further into conduction, which turns on current mirror Q5/Q6. Thus, the increase in Q3 emitter current is mirrored in an increase in Q6 collector current; the increased collector currents shunts more from the collector node and results in a decrease in base drive current for Q15. Besides avoiding wasting {{val|3|u=dB}} of gain here, this technique decreases common-mode gain and feedthrough of power supply noise.
-==== Voltage amplifier ====
-A current signal {{mvar|i}} at Q15's base gives rise to a current in Q19 of order {{math|''iβ''{{sup|2}}}} (the product of the {{math|''h''{{sub|fe}}}} of each of Q15 and Q19, which are connected in a [[Darlington pair]]). This current signal develops a voltage at the bases of output transistors Q14 and Q20 proportional to the {{math|''h''{{sub|ie}}}} of the respective transistor.
-==== Output amplifier ====
-Output transistors Q14 and Q20 are each configured as an emitter follower, so no voltage gain occurs there; instead, this stage provides current gain, equal to the {{math|''h''{{sub|fe}}}} of Q14 and Q20.
-The current gain lowers the output impedance and although the output impedance is not zero, as it would be in an ideal op amp, with negative feedback it approaches zero at low frequencies.
-=== Other linear characteristics ===
-==== Overall open-loop gain ====
-The net open-loop small-signal voltage gain of the op amp is determined by the product of the current gain {{math|''h''{{sub|fe}}}} of some 4 transistors. In practice, the voltage gain for a typical 741-style op amp is of order 200,000,<ref name="NS LM741" /> and the current gain, the ratio of input impedance (about {{val|2|-|6|u=MΩ}}) to output impedance (around {{val|50|u=Ω}}) provides yet more (power) gain.
-==== Small-signal common mode gain ====
-The ideal op amp has infinite [[common-mode rejection ratio]], or zero common-mode gain.
-In the present circuit, if the input voltages change in the same direction, the negative feedback makes Q3/Q4 base voltage follow (with {{math|2''V''{{sub|BE}}}} below) the input voltage variations. Now the output part (Q10) of Q10–Q11 current mirror keeps up the common current through Q9/Q8 constant in spite of varying voltage. Q3/Q4 collector currents, and accordingly the output current at the base of Q15, remain unchanged.
-In the typical 741 op amp, the common-mode rejection ratio is {{val|90|u=dB}},<ref name="NS LM741" /> implying an open-loop common-mode voltage gain of about 6.<!-- 200,000 / 10^^(4.5) -->
-==== Frequency compensation ====
-The innovation of the Fairchild μA741 was the introduction of [[frequency compensation]] via an on-chip (monolithic) capacitor, simplifying application of the op amp by eliminating the need for external components for this function. The {{val|30|u=pF}} capacitor stabilizes the amplifier via [[Miller effect|Miller compensation]] and functions in a manner similar to an op-amp [[integrator]] circuit. Also known as ''dominant [[Pole (complex analysis)|pole]] compensation'' because it introduces a pole that masks (dominates) the effects of other poles into the open loop frequency response; in a 741 op amp this pole can be as low as {{val|10|u=Hz}} (where it causes a {{val|-3|u=dB}} loss of open loop voltage gain).
-This internal compensation is provided to achieve [[BIBO stability|unconditional stability]] of the amplifier in negative feedback configurations where the feedback network is non-reactive and the [[loop gain]] is [[unity (mathematics)|unity]] or higher. In contrast, amplifiers requiring external compensation, such as the μA748, may require external compensation or closed-loop gains significantly higher than unity.
-==== Input offset voltage ====
-The ''offset null'' pins may be used to place external resistors (typically in the form of the two ends of a potentiometer, with the slider connected to {{math|''V''{{sub|S–}}}}) in parallel with the emitter resistors of Q5 and Q6, to adjust the balance of the Q5/Q6 current mirror. The potentiometer is adjusted such that the output is null (midrange) when the inputs are shorted together.
-=== Non-linear characteristics ===
-==== Input breakdown voltage ====
-The transistors Q3, Q4 help to increase the reverse {{math|''V''{{sub|BE}}}} rating; The base-emitter junctions of the NPN transistors Q1 and Q2 break down at around {{val|7|u=V}}, but the PNP transistors Q3 and Q4 have {{math|''V''{{sub|BE}}}} breakdown voltages around {{val|50|u=V}}.<ref>[http://ecow.engr.wisc.edu/cgi-bin/get/ece/342/schowalter/notes/chapter10/theua741operationalamplifier.ppt The μA741 Operational Amplifier]{{dead link|date=June 2016|bot=medic|fix-attempted=yes}}{{cbignore|bot=medic}}</ref>
-==== Output-stage voltage swing and current limiting ====
-Variations in the quiescent current with temperature, or due to manufacturing variations, are common, so [[crossover distortion]] may be subject to significant variation.
-The output range of the amplifier is about one volt less than the supply voltage, owing in part to {{math|''V''{{sub|BE}}}} of the output transistors Q14 and Q20.
-The {{val|25|u=Ω}} resistor at the Q14 emitter, along with Q17, limits Q14 current to about {{val|25|u=mA}}; otherwise, Q17 conducts no current. Current limiting for Q20 is performed in the voltage gain stage: Q22 senses the voltage across Q19's emitter resistor ({{val|50|u=Ω}}); as it turns on, it diminishes the drive current to Q15 base. Later versions of this amplifier schematic may show a somewhat different method of output current limiting.
-===Applicability considerations===
-While the 741 was historically used in audio and other sensitive equipment, such use is now rare because of the improved [[Noise (electronics)|noise]] performance of more modern op amps. Apart from generating noticeable hiss, 741s and other older op amps may have poor [[common-mode rejection ratio]]s and so will often introduce cable-borne mains hum and other common-mode interference, such as switch "clicks", into sensitive equipment.
-The '741' has come to often mean a generic op-amp IC (such as μA741, LM301, 558, LM324, TBA221 — or a more modern replacement such as the TL071). The description of the 741 output stage is qualitatively similar for many other designs (that may have quite different input stages), except:
-* Some devices (μA748, LM301, LM308) are not internally compensated. Hence, they provide a pin for wiring an external capacitor from output to some point within the operational amplifier, if used in low closed-loop gain applications.<ref>{{cite web |url=https://datasheet.octopart.com/UA748HC-Fairchild-Semiconductor-datasheet-182286989.pdf |title=μA748 Operational Amplifier |access-date=}}</ref>
-* Some modern devices have ''rail-to-rail'' output capability, meaning that the output can range from within a few millivolts of the positive supply voltage to within a few millivolts of the negative supply voltage.<ref name="rail-to-rail" />
 == Classification ==
+[[Image:LH033CG.jpg|right|thumb|LH0033CG: a high speed hybrid IC op amp]]
 Op amps may be classified by their construction:
 * discrete, built from individual [[transistor]]s or [[vacuum tube|tubes/valves]],
@@ Line 344: / Line 214: @@
 == Applications ==
-[[Image:Generic 741 pinout top.png|thumb|[[Dual in-line package|DIP]] [[pinout]] for 741-type operational amplifier]]
 {{Main|Operational amplifier applications}}
-=== Use in electronics system design ===
-{{Unreferenced section|date=September 2024}}
-The use of op amps as circuit blocks is much easier and clearer than specifying all their individual circuit elements (transistors, resistors, etc.), whether the amplifiers used are integrated or discrete circuits. In the first approximation op amps can be used as if they were ideal differential gain blocks; at a later stage, limits can be placed on the acceptable range of parameters for each op amp.
-Circuit design follows the same lines for all [[electronic circuit]]s. A specification is drawn up governing what the circuit is required to do, with allowable limits. For example, the gain may be required to be 100 times, with a tolerance of 5% but drift of less than 1% in a specified temperature range; the input impedance not less than one [[megohm]]; etc.
-A basic circuit is designed, often with the help of [[electronic circuit simulation]]. Specific commercially available op amps and other components are then chosen that meet the design criteria within the specified tolerances at acceptable cost. If not all criteria can be met, the specification may need to be modified.
-A prototype is then built and tested; additional changes to meet or improve the specification, alter functionality, or reduce the cost, may be made.
-=== Applications without feedback ===
-Without feedback, the op amp may be used as a [[voltage comparator]]. Note that a device designed primarily as a comparator may be better if, for instance, speed is important or a wide range of input voltages may be found since such devices can quickly recover from full-on or full-off ''saturated'' states.
-A ''voltage level detector'' can be obtained if a reference voltage ''V''<sub>ref</sub> is applied to one of the op amp's inputs. This means that the op amp is set up as a comparator to detect a positive voltage. If the voltage to be sensed, ''E''<sub>i</sub>, is applied to op amp's (+) input, the result is a noninverting positive-level detector: when ''E''<sub>i</sub> is above ''V''<sub>ref</sub>, ''V''<sub>O</sub> equals +''V''<sub>sat</sub>; when ''E''<sub>i</sub> is below ''V''<sub>ref</sub>, ''V''<sub>O</sub> equals −''V''<sub>sat</sub>. If ''E''<sub>i</sub> is applied to the inverting input, the circuit is an inverting positive-level detector: When ''E''<sub>i</sub> is above ''V''<sub>ref</sub>, ''V''<sub>O</sub> equals −''V''<sub>sat</sub>.
-A ''zero voltage level detector'' (''E''<sub>i</sub> = 0) can convert, for example, the output of a sine-wave from a function generator into a variable-frequency square wave. If ''E''<sub>i</sub> is a sine wave, triangular wave, or wave of any other shape that is symmetrical around zero, the zero-crossing detector's output will be square. Zero-crossing detection may also be useful in triggering [[TRIAC]]s at the best time to reduce mains interference and current spikes.
-===Positive-feedback applications===
-[[Image:Op-Amp Schmitt Trigger.svg|right|thumb|300px|Schmitt trigger implemented by a non-inverting comparator]]
-Another typical configuration of op amps is with positive feedback, which takes a fraction of the output signal back to the non-inverting input. An important application of positive feedback is the comparator with hysteresis, the [[Schmitt trigger]].
-Some circuits may use ''positive'' feedback and ''negative'' feedback around the same amplifier, for example [[triangle wave|triangle-wave]] [[oscillator]]s and [[active filters]].
-===Negative-feedback applications===
-==== Non-inverting amplifier ====
-[[Image:Op-Amp Non-Inverting Amplifier.svg|frame|An op amp connected in the non-inverting amplifier configuration]]
-In a non-inverting amplifier, the output voltage changes in the same direction as the input voltage.
-The gain equation for the op amp is
-:<math>V_\text{out} = A_\text{OL} (V_+ - V_-).</math>
-However, in this circuit ''V''<sub>−</sub> is a function of ''V''<sub>out</sub> because of the negative feedback through the ''R''<sub>1</sub> ''R''<sub>2</sub> network. ''R''<sub>1</sub> and ''R''<sub>2</sub> form a [[voltage divider]], and as ''V''<sub>−</sub> is a high-impedance input, it does not load it appreciably. Consequently
-:<math>V_- = \beta V_\text{out},</math>
-where
-:<math>\beta = \frac{R_1}{R_1 + R_2}.</math>
-Substituting this into the gain equation, we obtain
-:<math>V_\text{out} = A_\text{OL} (V_\text{in} - \beta V_\text{out}).</math>
-Solving for <math>V_\text{out}</math>:
-:<math>V_\text{out} = V_\text{in} \left( \frac{1}{\beta + \frac{1}{A_\text{OL}}} \right).</math>
-If <math>A_\text{OL}</math> is very large, this simplifies to
-:<math>
-  V_\text{out} \approx \frac{V_\text{in}}{\beta}
-                     = \frac{V_\text{in}}{\frac{R_1}{R_1 + R_2}}
-                     = V_\text{in} \left(1 + \frac{R_2}{R_1}\right).
-</math>
-The non-inverting input of the operational amplifier needs a path for DC to ground; if the signal source does not supply a DC path, or if that source requires a given load impedance, then the circuit will require another resistor from the non-inverting input to ground. When the operational amplifier's input bias currents are significant, then the DC source resistances driving the inputs should be balanced.<ref>An input bias current of 1&nbsp;μA through a DC source resistance of 10&nbsp;kΩ produces a 10&nbsp;mV offset voltage. If the other input bias current is the same and sees the same source resistance, then the two input offset voltages will cancel out. Balancing the DC source resistances may not be necessary if the input bias current and source resistance product is small.</ref> The ideal value for the feedback resistors (to give minimal offset voltage) will be such that the two resistances in parallel roughly equal the resistance to ground at the non-inverting input pin. That ideal value assumes the bias currents are well matched, which may not be true for all op amps.<ref>{{cite web |author=Analog Devices |title=Op Amp Input Bias Current |date=2009 |id=Tutorial MT-038 |publisher=Analog Devices |url=http://www.analog.com/static/imported-files/tutorials/MT-038.pdf |access-date=2014-05-15 |archive-date=2015-02-13 |archive-url=https://web.archive.org/web/20150213055046/http://www.analog.com/static/imported-files/tutorials/MT-038.pdf |url-status=dead }}</ref>
-==== Inverting amplifier ====
-[[Image:Op-Amp Inverting Amplifier.svg|frame|right|An op amp connected in the inverting amplifier configuration]]
-In an inverting amplifier, the output voltage changes in an opposite direction to the input voltage.
-As with the non-inverting amplifier, we start with the gain equation of the op amp:
-:<math>V_\text{out} = A_\text{OL} (V_+ - V_-).</math>
-This time, ''V''<sub>−</sub> is a function of both ''V''<sub>out</sub> and ''V''<sub>in</sub> due to the voltage divider formed by ''R''<sub>f</sub> and ''R''<sub>in</sub>. Again, the op-amp input does not apply an appreciable load, so
-:<math>V_- = \frac{1}{R_\text{f} + R_\text{in}} \left( R_\text{f} V_\text{in} + R_\text{in} V_\text{out} \right).</math>
-Substituting this into the gain equation and solving for <math>V_\text{out}</math>:
-:<math>V_\text{out} = - V_\text{in} \frac{A_\text{OL} R_\text{f}}{R_\text{f} + R_\text{in} + A_\text{OL} R_\text{in}}.</math>
-If <math>A_\text{OL}</math> is very large, this simplifies to
-:<math>V_\text{out} \approx -V_\text{in} \frac{R_\text{f}}{R_\text{in}}.</math>
-A resistor is often inserted between the non-inverting input and ground (so both inputs see similar resistances), reducing the [[input offset voltage]] due to different voltage drops due to [[bias current]], and may reduce distortion in some op amps.
-A [[Capacitive coupling|DC-blocking]] [[capacitor]] may be inserted in series with the input resistor when a [[frequency response]] down to DC is not needed and any DC voltage on the input is unwanted. That is, the capacitive component of the input impedance inserts a DC [[complex zero|zero]] and a low-frequency [[complex pole|pole]] that gives the circuit a [[bandpass]] or [[high-pass]] characteristic.
-The potentials at the operational amplifier inputs remain virtually constant (near ground) in the inverting configuration. The constant operating potential typically results in distortion levels that are lower than those attainable with the non-inverting topology.{{cn|date=January 2025}}
-===Other applications===
-* audio and video [[preamplifiers]] and [[Buffer amplifier|buffer]]s
-* [[differential amplifier]]s
-* [[differentiator]]s and [[integrator]]s
-* [[Filter (signal processing)|filter]]s
-* [[precision rectifier]]s
-* precision [[peak detector]]s
-* voltage and current [[Voltage regulator|regulators]]
-* [[analog calculator]]s
-* [[analog-to-digital converter]]s
-* [[digital-to-analog converter]]s
-* [[electronic oscillator|oscillator]]s and [[signal generator]]s
-* [[Clipper (electronics)|clipper]]
-* [[Clamper (electronics)|clamper]] (dc inserter or restorer)
-* [[Log amplifier|log and antilog amplifiers]]
-Most single, dual and quad op amps available have a standardized pin-out which permits one type to be substituted for another without wiring changes. A specific op amp may be chosen for its open loop gain, bandwidth, noise performance, input impedance, power consumption, or a compromise between any of these factors.
 ==Historical timeline==
-'''1941: A vacuum tube op amp.''' An op amp, defined as a general-purpose, DC-coupled, high-gain, inverting feedback amplifier, is first found in {{US patent|2,401,779}} "Summing Amplifier" filed by [[Karl D. Swartzel Jr.]] of Bell Labs in 1941. This design used three [[vacuum tube]]s to achieve a gain of {{nowrap|90 dB}} and operated on voltage rails of {{nowrap|±350 V}}. It had a single inverting input rather than differential inverting and non-inverting inputs, as are common in today's op amps. Throughout [[World War II]], Swartzel's design proved its value by being liberally used in the M9 [[Director (military)|artillery director]] designed at Bell Labs. This artillery director worked with the [[SCR-584 radar]] system to achieve extraordinary hit rates (near 90%) that would not have been possible otherwise.<ref name="Jung-2004">{{cite book |title=Op Amp Applications Handbook |page=777 |chapter=Chapter 8: Op Amp History |first=Walter G. |last=Jung |publisher=Newnes |year=2004 |isbn=978-0-7506-7844-5 |url=https://books.google.com/books?id=dunqt1rt4sAC |access-date=2008-11-15}}</ref>
+[[Image:K2-w Vacuum Tube Op-amp.jpg|upright|thumb|GAP/R K2-W: a vacuum-tube op amp (1953)]]
+'''1941: A vacuum tube op amp.''' An op amp, defined as a general-purpose, DC-coupled, high-gain, inverting feedback amplifier, is first found in {{US patent|2,401,779}} "Summing Amplifier" filed by [[Karl D. Swartzel Jr.]] of [[Bell Labs]] in 1941. This design used three [[vacuum tube]]s to achieve a gain of {{nowrap|90 dB}} and operated on voltage rails of {{nowrap|±350 V}}. It had a single inverting input rather than differential inverting and non-inverting inputs, as are common in today's op amps. Throughout [[World War II]], Swartzel's design proved its value by being liberally used in the M9 [[Director (military)|artillery director]] designed at Bell Labs. This artillery director worked with the [[SCR-584 radar]] system to achieve extraordinary hit rates (near 90%) that would not have been possible otherwise.<ref name="Jung-2004">{{cite book |title=Op Amp Applications Handbook |page=777 |chapter=Chapter 8: Op Amp History |first=Walter G. |last=Jung |publisher=Newnes |year=2004 |isbn=978-0-7506-7844-5 |url=https://books.google.com/books?id=dunqt1rt4sAC |access-date=2008-11-15}}</ref>
-[[Image:K2-w Vacuum Tube Op-amp.jpg|right|thumb|120px|GAP/R K2-W: a vacuum-tube op amp (1953)]]
 '''1947: An op amp with an explicit non-inverting input.''' In 1947, the operational amplifier was first formally defined and named in a paper by [[John R. Ragazzini]] of Columbia University.<ref>{{cite journal |last1=Ragazzini |first1=John R. |author1-link=John R. Ragazzini |last2=Randall |first2=Robert H. |last3=Russell |first3=Frederick A. |title=Analysis of Problems in Dynamics by Electronic Circuits |journal=Proceedings of the IRE |volume=35 |issue=5 |pages=444–452 |publisher=IEEE |date=May 1947 |issn=0096-8390 |doi=10.1109/JRPROC.1947.232616}}</ref> In this same paper a footnote mentioned an op-amp design by a student that would turn out to be quite significant. This op amp, designed by [[Loebe Julie]], had two major innovations. Its input stage used a long-tailed [[triode]] pair with loads matched to reduce drift in the output and, far more importantly, it was the first op-amp design to have two inputs (one inverting, the other non-inverting). The differential input made a whole range of new functionality possible, but it would not be used for a long time due to the rise of the chopper-stabilized amplifier.<ref name="Jung-2004"/>
@@ Line 457: / Line 224: @@
 '''1949: A chopper-stabilized op amp.''' In 1949, Edwin A. Goldberg designed a [[Chopper (electronics)|chopper]]-stabilized op amp.<ref>{{cite web |url=http://www.analog.com/library/analogDialogue/archives/39-05/Web_ChH_final.pdf |title=Op Amp Applications |publisher=[[Analog Devices]] |access-date=2012-12-27 |url-status=dead |archive-url=https://web.archive.org/web/20121007072916/http://www.analog.com/library/analogDialogue/archives/39-05/Web_ChH_final.pdf |archive-date=2012-10-07 }}</ref> This set-up uses a normal op amp with an additional [[Alternating current|AC]] amplifier that goes alongside the op amp. The chopper gets an AC signal from [[Direct current|DC]] by switching between the DC voltage and ground at a fast rate (60 or 400&nbsp;Hz). This signal is then amplified, rectified, filtered and fed into the op amp's non-inverting input. This vastly improved the gain of the op amp while significantly reducing the output drift and DC offset. Unfortunately, any design that used a chopper couldn't use the non-inverting input for any other purpose. Nevertheless, the much-improved characteristics of the chopper-stabilized op amp made it the dominant way to use op amps. Techniques that used the non-inverting input were not widely practiced until the 1960s when op-amp [[Integrated circuit|IC]]s became available.
-'''1953: A commercially available op amp.''' In 1953, vacuum tube op amps became commercially available with the release of the model K2-W from [[George A. Philbrick]] Researches, Incorporated. The designation on the devices shown, GAP/R, is an acronym for the complete company name. Two nine-pin [[12AX7]] vacuum tubes were mounted in an octal package and had a model K2-P chopper add-on available. This op amp was based on a descendant of Loebe Julie's 1947 design and, along with its successors, would start the widespread use of op amps in industry.<ref>{{citation |url=https://www.analog.com/media/en/training-seminars/design-handbooks/Op-Amp-Applications/SectionH.pdf |title=Op Amp History |access-date=2025-06-02 |publisher=[[Analog Devices]] |pages=20–21}}</ref><!--[[User:Kvng/RTH]]-->
+'''1953: A commercially available op amp.''' In 1953, vacuum tube op amps became commercially available with the release of the model K2-W from [[George A. Philbrick]] Researches, Incorporated. The designation on the devices shown, GAP/R, is an acronym for the complete company name. Two nine-pin [[12AX7]] vacuum tubes were mounted in an octal package and had a model K2-P chopper add-on available. This op amp was based on a descendant of Loebe Julie's 1947 design and, along with its successors, would start the widespread use of op amps in industry.<ref>{{citation |url=https://www.analog.com/media/en/training-seminars/design-handbooks/Op-Amp-Applications/SectionH.pdf |title=Op Amp History |access-date=2025-06-02 |publisher=[[Analog Devices]] |pages=20–21}}</ref>
-[[Image:Discrete opamp.png|right|thumb|120px|GAP/R model P45: a solid-state, discrete op amp (1961).]]
+{{clear}}
+[[Image:Discrete opamp.png|thumb|GAP/R model P45: a solid-state, discrete op amp (1961).]]
 '''1961: A discrete IC op amp.''' With the birth of the [[transistor]] in 1947, and the silicon transistor in 1954, the concept of ICs became a reality. The introduction of the [[planar process]] in 1959 made transistors and ICs stable enough to be commercially useful. By 1961, solid-state, discrete op amps were being produced. These op amps were effectively small circuit boards with packages such as [[edge connector]]s. They usually had hand-selected resistors in order to improve things such as voltage offset and drift. The P45 (1961) had a gain of 94&nbsp;dB and ran on ±15&nbsp;V rails. It was intended to deal with signals in the range of {{nowrap|±10 V}}.
 '''1961: A varactor bridge op amp.''' There have been many different directions taken in op-amp design. [[Varactor]] bridge op amps started to be produced in the early 1960s.<ref>{{cite web |url=http://www.philbrickarchive.org/ |title=The Philbrick Archive |website=www.philbrickarchive.org |access-date=28 April 2018 |url-status=live |archive-url=https://archive.today/20120907192216/http://www.philbrickarchive.org/ |archive-date=7 September 2012 }}</ref><ref>June 1961 advertisement for Philbrick P2, {{cite web |url=http://www.philbrickarchive.org/p2%20and%206033%20ad%20rsi%20vol32%20no6%20june1961.pdf |title=The all-new, all solid-state Philbrick P2 amplifier |access-date=2011-05-11 |url-status=live |archive-url=https://web.archive.org/web/20111008160503/http://www.philbrickarchive.org/p2%20and%206033%20ad%20rsi%20vol32%20no6%20june1961.pdf |archive-date=2011-10-08 }}</ref> They were designed to have extremely small input current and are still amongst the best op amps available in terms of common-mode rejection with the ability to correctly deal with hundreds of volts at their inputs.
-[[Image:Modular opamp.png|right|thumb|120px|GAP/R model PP65: a solid-state op amp in a potted module (1962)]]
+{{clear}}
+[[Image:Modular opamp.png|thumb|GAP/R model PP65: a solid-state op amp in a potted module (1962)]]
 '''1962: An op amp in a potted module.''' By 1962, several companies were producing modular potted packages that could be plugged into [[printed circuit board]]s.{{Citation needed|date=January 2009}} These packages were crucially important as they made the operational amplifier into a single [[black box]] which could be easily treated as a component in a larger circuit.
-'''1963: A monolithic IC op amp.''' In 1963, the first monolithic IC op amp, the μA702 designed by [[Bob Widlar]] at Fairchild Semiconductor, was released. Monolithic [[Integrated circuit|IC]]s consist of a single chip as opposed to a chip and discrete parts (a discrete IC) or multiple chips bonded and connected on a circuit board (a hybrid IC). Almost all modern op amps are monolithic ICs; however, this first IC did not meet with much success. Issues such as an uneven supply voltage, low gain and a small dynamic range held off the dominance of monolithic op amps until 1965 when the μA709<ref>{{cite book |first=A. P. |last=Malvino |title=Electronic Principles |edition=2nd |date=1979 |isbn=0-07-039867-4 |page=[https://archive.org/details/electronicprinci00malv/page/476 476] |publisher=McGraw-Hill |url=https://archive.org/details/electronicprinci00malv/page/476 }}</ref> (also designed by Bob Widlar) was released.
+'''1963: A monolithic IC op amp.''' In 1963, the first monolithic IC op amp, the μA702 designed by Bob Widlar at Fairchild Semiconductor, was released. Monolithic ICs consist of a single chip as opposed to a chip and discrete parts (a discrete IC) or multiple chips bonded and connected on a circuit board (a hybrid IC). Almost all modern op amps are monolithic ICs; however, this first IC did not meet with much success. Issues such as an uneven supply voltage, low gain and a small dynamic range held off the dominance of monolithic op amps until 1965 when the μA709<ref>{{cite book |first=A. P. |last=Malvino |title=Electronic Principles |edition=2nd |date=1979 |isbn=0-07-039867-4 |page=[https://archive.org/details/electronicprinci00malv/page/476 476] |publisher=McGraw-Hill |url=https://archive.org/details/electronicprinci00malv/page/476 }}</ref> (also designed by Bob Widlar) was released.
-'''1968: Release of the μA741.''' The popularity of monolithic op amps was further improved upon the release of the LM101 in 1967, which solved a variety of issues, and the subsequent release of the μA741 in 1968. The μA741 was extremely similar to the LM101 except that Fairchild's facilities allowed them to include a 30&nbsp;pF compensation capacitor inside the chip instead of requiring external compensation. This simple difference has made the 741 ''the'' canonical op amp and many modern amps base their pinout on the 741s. The μA741 is still in production, and has become ubiquitous in electronics—many manufacturers produce a version of this classic chip, recognizable by part numbers containing ''741''. The same part is manufactured by several companies.
+'''1968: Release of the [[741_(operational_amplifier)|μA741]].''' The popularity of monolithic op amps was further improved with the release of the LM101 in 1967, which solved a variety of issues, and the subsequent release of the μA741 in 1968. The μA741 was extremely similar to the LM101 except that Fairchild's manufacturing processes allowed them to include a 30&nbsp;pF compensation capacitor inside the chip instead of requiring external compensation. This simple difference has made the 741 a canonical op amp and a range of modern amps base their pinout on the 741s. The μA741 is still in production, and has become ubiquitous in electronics—many manufacturers produce a version of this classic chip, recognizable by part numbers containing ''741''.
 '''1970: First high-speed, low-input current FET design.'''
-In the 1970s high speed, low-input current designs started to be made by using [[FET]]s. These would be largely replaced by op amps made with [[MOSFET]]s in the 1980s.
+In the 1970s high-speed, low-input current designs started to be made by using [[FET]]s. These would be largely replaced by op amps made with [[MOSFET]]s in the 1980s.
-[[Image:LH033CG.jpg|right|thumb|120px|LH0033CG: a  high speed hybrid IC  op amp]]
-'''1972: Single sided supply op amps being produced.''' A single sided supply op amp is one where the input and output voltages can be as low as the negative power supply voltage instead of needing to be at least two volts above it. The result is that it can operate in many applications with the negative supply pin on the op amp being connected to the signal ground, thus eliminating the need for a separate negative power supply.
-The LM324 (released in 1972) was one such op amp that came in a quad package (four separate op amps in one package) and became an industry standard. In addition to packaging multiple op amps in a single package, the 1970s also saw the birth of op amps in hybrid packages. These op amps were generally improved versions of existing monolithic op amps. As the properties of monolithic op amps improved, the more complex hybrid ICs were quickly relegated to systems that are required to have extremely long service lives or other specialty systems.
-[[Image:LM741CN.jpg|right|thumb|120px|An op amp in a mini DIP package]]
+'''1972: Single-sided supply op amps being produced.''' A single-sided supply op amp is one where the input and output voltages can be as low as the negative power supply voltage instead of needing to be at least two volts above it. The result is that it can operate in many applications with the negative supply pin on the op amp being connected to the signal ground, thus eliminating the need for a separate negative power supply. The [[LM324]], released in 1972, was one such op amp that came in a quad package (four separate op amps in one package) and became an industry standard.
-'''Recent trends.''' Recently{{when?|date=February 2023}} supply voltages in analog circuits have decreased (as they have in digital logic) and low-voltage op amps have been introduced reflecting this. Supplies of 5&nbsp;V and increasingly 3.3&nbsp;V (sometimes as low as 1.8&nbsp;V) are common. To maximize the signal range modern op amps commonly have rail-to-rail output (the output signal can range from the lowest supply voltage to the highest) and sometimes rail-to-rail inputs.<ref name="rail-to-rail" />
+'''Recent trends.'''
+Supply voltages in analog circuits have decreased (as they have in digital logic) and low-voltage op amps have been introduced reflecting this. Supplies of 5&nbsp;V and increasingly 3.3&nbsp;V (sometimes as low as 1.8&nbsp;V) are common. To maximize the signal range, modern op amps commonly have rail-to-rail output (the output signal can range from the lowest supply voltage to the highest) and sometimes rail-to-rail inputs.<ref name="rail-to-rail" />
 == See also ==
 {{Portal|Electronics}}
-{{div col|colwidth=20em}}
+* [[µA741]]
-* [[Active filter]]
-* [[Analog computer]]
-* [[Bob Widlar]]
 * [[Current conveyor]]
-* [[Current-feedback operational amplifier]]
+* {{slink|DIY audio|Operational amplifier swapping}}
-* [[Differential amplifier]]
-* [[George A. Philbrick]]
-* [[Instrumentation amplifier]]
 * [[List of LM-series integrated circuits]]
-* [[Negative feedback amplifier]]
-* [[Op-amp swapping]]
-* [[Operational amplifier applications]]
 * [[Operational transconductance amplifier]]
 * [[Sallen–Key topology]]
-{{div col end}}
 ==Notes==
@@ Line 545: / Line 298: @@
 ;Historical datasheets
-* [https://www.ti.com/lit/ds/symlink/lm201a-n.pdf LM301, Single BJT OpAmp, Texas Instruments]
+* [https://www.ti.com/lit/ds/symlink/lm201a-n.pdf LM301, Single BJT OpAmp], Texas Instruments
-* [https://web.archive.org/web/20081202220019/http://www.ti.com/lit/gpn/lm324 LM324, Quad BJT OpAmp, Texas Instruments]
+* [https://web.archive.org/web/20081202220019/http://www.ti.com/lit/gpn/lm324 LM324, Quad BJT OpAmp], Texas Instruments
-* [http://www.ti.com/lit/gpn/lm741 LM741, Single BJT OpAmp, Texas Instruments]
+* [http://www.ti.com/lit/gpn/lm741 LM741, Single BJT OpAmp], Texas Instruments
-* [http://www.ti.com/lit/gpn/ne5532 NE5532, Dual BJT OpAmp, Texas Instruments] (NE5534 is similar single)
+* [http://www.ti.com/lit/gpn/ne5532 NE5532, Dual BJT OpAmp], Texas Instruments (NE5534 is similar single)
-* [http://www.ti.com/lit/gpn/tl072 TL072, Dual JFET OpAmp, Texas Instruments] (TL074 is Quad)
+* [http://www.ti.com/lit/gpn/tl072 TL072, Dual JFET OpAmp], Texas Instruments (TL074 is Quad)<!--[[User:Kvng/RTH]]-->
 ==External links==

Operational amplifier: Difference between revisions

Latest revision as of 01:11, 18 November 2025

Operation

Open-loop amplifier

Closed-loop amplifier

Characteristics Script error: No such module "anchor".

Ideal op amps

Real op amps

Non-linear imperfections

Power considerations

Classification

Applications

Historical timeline

See also

Notes

References

Further reading

External links

Navigation menu

Search