View source for US Standard Light Rail Vehicle

{{Short description|Light rail vehicle}}
{{more citations needed|date=February 2013}}
{{use mdy dates|date=June 2015}}
{{Infobox Train
| name = US Standard Light Rail Vehicle
| image = San Francisco Boeing LRV at Duboce & Church, March 1980.jpg
| imagesize = 250px
| caption = A Boeing Vertol US SLRV in service for the [[San Francisco Municipal Railway]] in 1980, on the then-newly opened [[Muni Metro]]
| yearconstruction = 1976–1979
| yearservice = 1976–1984
| yearscrapped = 1987–as late as 2020
| numberbuilt = 275
| stocktype = 
| service = 1976-1998 (MUNI)<br/>1976-2007 (MBTA)
| carlength = {{convert|71|ft|m|sigfig=4|abbr=on}}<ref name=SLRV-I />
| width = {{convert|8|ft|10+1/4|in|mm|0|sigfig=4|abbr=on}}<ref name=SLRV-I />
| height = {{convert|11|ft|4|in|m|sigfig=4|abbr=on}}<ref name=SLRV-I /> ATOR
| floorheight = {{convert|34|in|cm|sigfig=3|abbr=on}}<ref name=SLRV-I /> ATOR
| platformheight = 
| entrylevelorstep = 
| art-sections = 
| weight = {{convert|67000|lb|sigfig=5|abbr=on}}<ref name=SLRV-I /> empty
| brakes = [[Railway airbrake|Air]]/[[Hydraulic brake|Hydraulic]] [[NY Air Brake]]
| traction = [[Garrett AiResearch]] [[chopper control]]<ref name=propulsion>{{Cite web |last=Museum |first=Western Railway |title=San Francisco Municipal Railway 1258 - Western Railway Museum |url=https://www.wrm.org/visit/car-roster/passenger-cars/light-rail/item/111-san-francisco-municipal-railway-1258 |access-date=2024-06-28 |website=www.wrm.org |language=en-gb}}</ref>
| uicclass = Bo’2Bo’
| aarwheels = B-2-B
| traction motors = 2x Garrett AiResearch {{convert|210|hp|sigfig=3|abbr=on|lk=on}}, 152 kV, 280 [[Volt|V]], 600 [[Ampere|A]] [[DC motor]], 1 per truck<ref name=propulsion />
| acceleration = {{convert|3.1|miles/hour/second|m/s/s|abbr=on}}<ref name=SLRV-I />
| engine = 
| maxspeed = {{convert|50|mph|km/h|sigfig=3|abbr=on}} with multiple units
| capacity = seated 52 (MBTA, later reduced to 48 to provide room for wheelchairs) or 68 (Muni), with [[crush load]] of 219
| gauge = {{RailGauge|ussg|allk=on}}
}}

The '''US Standard Light Rail Vehicle''' (SLRV) was a [[light rail]] vehicle (LRV) built by [[Boeing Rotorcraft Systems|Boeing Vertol]] in the 1970s. The [[Federal Transit Administration|Urban Mass Transportation Administration]] (UMTA) of the [[United States Department of Transportation]] (USDOT) promoted it as a standardized vehicle for U.S. cities. Part of a series of defense conversion projects in the waning days of the [[Vietnam War]], the SLRV was seen as both a replacement for older [[PCC streetcar]]s in many cities and as a catalyst for cities to construct new light rail systems. The US SLRV was marketed as and is popularly known as the '''Boeing LRV''' or '''SLRV''', and should not be confused with their prior [[lunar rover|lunar roving vehicles]] for [[NASA]].

The SLRV was purchased by the public transportation operators of [[Massachusetts Bay Transportation Authority|Boston]] and [[San Francisco Municipal Railway|San Francisco]]. In service by 1976, the US SLRV proved to be unreliable and scrapping started as early as 1987, but the SLRVs were not completely replaced on both systems until 2007. Although the SLRV itself was not successful due to poor reliability, it did set the general size and configuration for succeeding LRVs in the United States.

==History==
===Origin===
[[File:MBTA 3400 Type 6 mockup at the Seashore Trolley Museum 327 (36889642793).jpg|thumb|left|MBTA #3400 Type 6 wooden mockup from 1968, stored at [[Seashore Trolley Museum]] (2017)]]
The original concept of the SLRV came to fruition in the late 1960s as the limited number of cities with PCCs in [[North America]] were looking for modern replacements for their aging rolling stock; the last PCC had been manufactured in 1952.<ref>{{cite web |url=https://www.streetcar.org/car_1040_newest_all_over_again/ |title=Car 1040: Newest All Over Again |date=December 16, 2011 |website=Market Street Railway |access-date=2 January 2019}}</ref> In 1968, the [[Massachusetts Bay Transportation Authority|MBTA]] in [[Boston]], one operator of PCC streetcars, created a mockup for one end of a proposed "Type 6" streetcar out of wood; the Type 6 program was discontinued after MBTA decided the cost to produce it was too high.<ref>{{cite web |url=http://www.bostonstreetcars.com/trolley-types-of-boston.html |title=Trolley Types of Boston |author=Propp, Gil |publisher=Boston Streetcars |access-date=2 January 2019}}</ref> Meanwhile, [[San Francisco Municipal Railway|Muni]] in [[San Francisco]], released a request for proposals in 1971 to purchase 78 new cars, designed by the rail transit engineering firm Louis T. Klauder and Associates (LTK), to replace their aging PCC fleet.<ref name=UMTA-NALRV /> The new cars, which Muni called subway-streetcars, were touted as "specially designed for San Francisco, adaptable to both subway and surface conditions and seating more passengers than the present [PCC] streetcars."<ref>{{cite report |url=https://archive.org/details/improvementplanf71sanf/page/44 |title=Improvement Plan for Transportation |date=1971 |publisher=San Francisco Department of City Planning |access-date=19 December 2018}}</ref> Muni received two bids in November 1971, with a low bid price of {{USD|473000|1971|round=-4}} per car from Boeing.<ref name=TX-1980>{{cite report |url=https://library.ctr.utexas.edu/digitized/texasarchive/phase2/1058-1f.pdf |title=An evaluation of the applicability of light rail transit to Texas cities |author1=Walton, C. Michael |author2=Black, Alan |author3=Cervenka, Kenneth J. |author4=Nichols, Kathryn |date=August 1980 |publisher=Texas State Department of Highways and Public Transportation; Transportation Planning Division |access-date=27 December 2018}}</ref>{{rp|95;220}} Both bids were rejected as being excessively costly because potential builders were forced to recoup development costs over a relatively small number of vehicles.<ref name=UMTA-NALRV/>

{{multiple image |align=right |direction=vertical
 |image1=Modern Edmonton streetcar -d.jpg
 |caption1=Siemens-Düwag car 601 ([[:de:TW 601|DE]]), 1970 "Hanover" prototype for the [[Hanover Stadtbahn]]<ref>{{cite magazine |url=http://www.trolleycoalition.org/pdf/bulletin35.pdf |title=Edmonton's Hanover 601 Streetcar returned to Germany |magazine=Transit Talk |volume=35 |publisher=Electric Traction Committee of the Edmonton Trolley Coalition |date=November 2016 |access-date=3 June 2019}}</ref>
 |image2=LTK-1971 (N-Judah).jpg
 |caption2=Exterior view of the Louis T. Klauder-designed subway-streetcars for San Francisco (1971)
 |image3=SLRV Engineering Fig 1-1 (1979).jpg
 |caption3=US SLRV at Pueblo for testing (1976). This car bears Muni [[Walter Landor|Landor]]/"Sunset" livery, the MBTA logo, and Boeing branding on the nose.}}
Düwag had built a prototype as a demonstrator for the [[Hanover Stadtbahn]] in 1970 (Hanover car 601 {{bracket|[[:de:TW 601|DE]]}}); in June 1971 MBTA ordered two more prototype "Hanover" cars, to be partially paid using a grant from UMTA. However, under [[Nixon shock|the Nixon administration's "New Economic Policy"]] introduced that fall, UMTA was not allowed to fund the grant.<ref name=UMTA-NALRV /><ref name=H6227/>{{rp|19}} That policy, codified as "Buy America" in Title IV of the Surface Transportation Assistance Act of 1978, stated that UMTA could not fund any grants exceeding $500,000 for transit vehicles that were produced outside the United States unless an exception was approved by the Secretary of Transportation.<ref>{{USBill|95|HR|11733}}&nbsp;[https://www.govinfo.gov/content/pkg/STATUTE-92/pdf/STATUTE-92-Pg2689.pdf#page=68 direct URL]</ref> Instead, Boston (MBTA) was directed to join with San Francisco (Muni) and Philadelphia (SEPTA) to design a new streetcar that could meet the needs of all three cities.<ref name=Boston-1980/>

In response to the failure to procure the Type 6, [[Duewag]], and LTK/Muni streetcars, UMTA organized the BSF (Boston and San Francisco) Committee to design a standardized light rail car to reduce per-unit costs, using the same concept under which the earlier PCC streetcars were designed.<ref name=UMTA-NALRV>{{cite conference |url=http://onlinepubs.trb.org/Onlinepubs/sr/sr161/sr161-012.pdf |title=North American Light Rail Vehicles |author1=Silen, Joseph S. |author2= Mora, Jeffrey G. |date=June 1975 |location=Philadelphia, Pennsylvania |conference=National Conference on Light Rail Transit |pages=93–98 |publisher=Transportation Research Board |access-date=18 December 2018}}</ref> The Standard Light Rail Vehicle (SLRV) specification was developed by UMTA based on the 1971 LTK design for Muni in conjunction with potential operators (who were all currently operating PCCs) in Boston, San Francisco, [[Southeastern Pennsylvania Transportation Authority|Philadelphia (SEPTA)]], [[Shaker Heights Rapid Transit|Cleveland (Shaker Heights)]], [[Port Authority of Allegheny County|Pittsburgh (Port Authority)]], [[Transport of New Jersey|New Jersey]], [[El Paso City Lines|El Paso (City Lines)]], and [[Toronto Transit Commission|Toronto (TTC)]] as well as industry consultants at [[WSP USA|Parsons Brinckerhoff]] and Louis T. Klauder and Associates.<ref name=SLRV-I>{{cite report |url=https://rosap.ntl.bts.gov/view/dot/10641/dot_10641_DS1.pdf |title=SLRV engineering tests at Department of Transportation, Transportation Test Center: Final Test Report, No. UMTA-MA-06-0025-79-3 |volume=I |date=June 1979 |pages=93–98 |author=Boeing Vertol Company |publisher=U.S. Department of Transportation, Urban Mass Transportation Administration |access-date=18 December 2018}}</ref><ref name=UMTA-NALRV/> At the same time, a flood of defense conversion projects came to fruition as the result of government encouragement to help keep defense suppliers busy as the Vietnam War was coming to an end.<ref name=Boeing>{{cite web |url=https://www.boeing.com/history/products/rapid-transit-car.page |title=Historical Snapshot: Light Rail Vehicle/Rapid Transit Car |website=Boeing |access-date=19 December 2018}}</ref>

===Contracts awarded===
UMTA awarded a grant for {{USD|33000000|round=-5}} to MBTA on October 20, 1972, towards the purchase of 150 SLRVs. On April 23, 1973, MBTA signed a contract with Boeing Vertol for the 150 SLRVs.<ref name=H6227 />{{rp|6}} On May 1, 1973, UMTA awarded Boeing-Vertol of [[Philadelphia]], [[Pennsylvania]] the contract to produce the SLRV<ref name=GAO-MBTA-80>{{cite report |url=https://www.gao.gov/assets/140/130883.pdf |title=Massachusetts Bay Transportation Authority's Termination of Contract for Light Rail Vehicles PSAD-81-11 |author=Sheley Jr., W. H. |date=November 10, 1980 |publisher=United States General Accounting Office |access-date=22 December 2018}}</ref> at a cost of approximately $300,000 per car, {{USD|316616|1972|round=-4}} each for the Muni configuration and {{USD|293422|1972|round=-4}} each for the MBTA configuration.<ref name=UMTA-NALRV/><ref name="TheyKnewAboutIt">{{cite news|last=Sullivan|first=Kathleen| title=Muni knew about trolley lemons in '70s: Test runs in Boston found major trouble in many systems | date=September 14, 1998 | newspaper=[[The San Francisco Examiner]] | page=A | url=http://www.sfgate.com/default/article/Muni-knew-about-trolley-lemons-in-70s-3070106.php |access-date=December 7, 2012}}</ref> Muni initially ordered 80 cars and the MBTA ordered 150, and production commenced the same day the contract was awarded<ref name=Boeing/> at a combined cost of {{USD|69000000|1973|round=-5}}.<ref>Boeing bids low on Light Rail Vehicles ''[[Railway Age]]'' February 26, 1973 page 8</ref> MBTA was scheduled to receive its first SLRV for testing in February 1975, and the majority of its cars in 1976.<ref>{{cite news |url=https://www.newspapers.com/newspage/435883779/ |title=Green Line scheduled to get 150 cars by 1976: Pa. firm tooling up to construct deluxe trolleys for MBTA |author=Plotkin, A. S. |date=May 9, 1973 |newspaper=[[The Boston Globe]] |access-date=2 January 2019}} {{subscription required}}</ref> The MBTA portion of the contract cost {{USD|44000000|1973|round=-5}} for 150 cars; later, the orders were expanded to 100 and 175 respectively,<ref name="BoeingsForScrapOrSale!">{{cite news|last=Lelchuk|first=Ilene| title=Muni cars on a roll into city junkyard: Even preservationists reject the clunkers | date=January 14, 2002 | newspaper=[[San Francisco Chronicle]] | page=B-1| url=http://www.sfgate.com/default/article/Muni-cars-on-a-roll-into-city-junkyard-Even-2883855.php |access-date=December 7, 2012}}</ref> and the extra 25 cars for MBTA added another {{USD|7600000|1974|round=-4}},<ref name=Boston-1980/> of which UMTA awarded MBTA {{USD|7000000|1974|round=-4}} on June 10, 1974.<ref name=H6227/>{{rp|6}} The SLRV was the first American-built trolley since 1952.<ref name=PopSci76>{{cite magazine |url=https://books.google.com/books?id=wAEAAAAAMBAJ&pg=PA60 |title=Space-age trolleys—they're making a clanging comeback |author=Shuldiner, Herbert |date=January 1976 |magazine=Popular Science |publisher=Times Mirror Magazines |volume=208 |number=1 |pages=60–61;111;113 |access-date=20 December 2018}}</ref>

In late 1974, the first new SLRV was operated on a short test track at the Boeing plant.<ref name=UMTA-NALRV /> The first demonstrator model was produced in 1975 and was intended to be an early Muni car,<ref name="TheyKnewAboutIt" /> and ran tests in Boston for 11 weeks.<ref name=Bei-78 /> Three cars (two in the Muni configuration, and one in the MBTA configuration) were shipped to the [[Transportation Test Center]] in [[Pueblo, Colorado]] in fall 1975<ref name=Bei-78 /> under a contract awarded to Boeing Vertol for engineering testing.<ref name=SLRV-I /> MBTA received its first car for testing in September 1976,<ref name=H6227/>{{rp|6}} two years behind schedule.<ref name=Boston-1980/>  This first car was delivered with [[trolley pole]]s in addition to the pantograph, as the MBTA was still in the process of reconfiguring its overhead lines to accommodate the latter.

===Operators===
{{multiple image |align=right |direction=vertical |header=US SLRVs in service with the only two operators: MBTA and Muni
 |image1=1977 Boeing LRV 3466 of MBTA (Boston) at Beacon and Hawes in 1987.jpg
 |caption1=MBTA #3466 at [[Hawes Street station|Hawes Street stop]] (1987)
 |image2=Train of Boeing LRVs waiting to depart Muni Metro's Embarcadero station in 1993.jpg
 |caption2=Muni #1306 forming part of a two-car train in the [[Market Street subway]], in San Francisco (1993)
}}
The first four SLRVs (3415, 3416, 3418, and 3421) entered revenue service on December 30, 1976, on the MBTA's [[Green Line D branch]].<ref name=Boston-1980/><ref name=farewell-3418>{{cite web |url=http://members.aol.com/smoore5049/3418/3418.html |title=Boeing-Vertol LRV 3418 Fantrip |date=June 1, 1997 |author=Moore, Scott |publisher=AOL |archive-url=https://web.archive.org/web/20000124154322/http://members.aol.com/smoore5049/3418/3418.html |archive-date=24 January 2000 |url-status=dead}}</ref> However, revenue service with the SLRVs was suspended on April 16, 1977 due to numerous derailments, with 31 SLRVs delivered at that point.<ref name=H6227/>{{rp|19}} In San Francisco, the first two SLRVs were delivered in October 1977, and as with Boston's first car, these cars featured trolley poles as conversion to [[Pantograph (transport)|pantograph]] collection was not yet complete.  Production models were delivered starting in December 1978, these cars having only pantographs, at which time the two pilot cars were returned to Boeing, and later re-delivered without the poles.<ref name=OERHS-1213/> The first regular runs on the Muni system came on April 23, 1979, on a temporary shuttle service, with more extensive use beginning with the opening of the [[Muni Metro]] on February 18, 1980.<ref name=perles1981>{{cite book|last=Perles|first=Anthony|title=The People's Railway: The History of the Municipal Railway of San Francisco|year=1981|publisher=[[Interurban Press]]|location=Glendale, CA (US)|isbn=0-916374-42-4|pages=234, 245, 250}}</ref><ref name=Callwell99/>{{rp|56–57}}

Because the layout of Muni had several branch lines converging into the [[Twin Peaks Tunnel]] at West Portal and more lines merging near Church, Muni SLRVs were intended to couple in up to a 4-car consist as they entered the tunnel and underground portions of the route; as they exited, they would uncouple to continue on their assigned lines.<ref name=Bei-78 /> However, due to slow door cycling and a 3-second delay between the operator signal and actual brake release, the Muni SLRVs proved to be slower than the PCCs in surface operation, and Muni was unable to meet the planned 4-minute headways on individual lines that would allow 2-minute headways with coupled trains underground. In addition, trains could not be turned around to meet 2-minute headways at the terminal Embarcadero Station.<ref>{{cite conference |url=http://onlinepubs.trb.org/Onlinepubs/sr/sr195/sr195-034.pdf |title=San Francisco Muni Metro: Operating Issues and Strategies |author1=Rosen, Daniel |author2=Olson, Leonard |date=March 1982 |conference=Conference on Light Rail Transit |location=San Diego, California |publisher=Transportation Research Board |pages=141–144 |access-date=26 December 2018}}</ref> A new {{convert|6.5|acre|abbr=on|adj=on}} Muni Metro Rail Center (later renamed the Curtis E. Green Light Rail Center) was constructed for storage and maintenance near the [[Balboa Park station]]<ref name=Bei-78 /> after Muni decided to purchase the cars the MBTA had rejected.<ref name=Perles-84/>

The [[Greater Cleveland Regional Transit Authority]] tested MBTA car #3401 on [[Blue and Green Lines (Cleveland)|former interurban lines]] in mid-1976, but ultimately declined to purchase the US SLRV, instead buying custom LRVs of a different design from [[Società Italiana Ernesto Breda|Breda Costruzioni Ferroviarie]].<ref name=rollsign198203 /> When Cleveland released a request for quote in September 1977, Boeing Vertol bid {{USD|869492|1977|round=-5}} per SLRV, exceeding Breda's winning bid of {{USD|645833|1977|round=-5}} per car.<ref name=TX-1980/>{{rp|221}}<ref name=GAO-MBTA-80 /><ref name=Lea-79>{{cite report |url=https://ntrl.ntis.gov/NTRL/ |title=Cost Savings Potential of Modifications to the Standard Light Rail Vehicle Specification |publisher=Urban Mass Transportation Administration, US Department of Transportation |author=N.D. Lea & Associates |date=February 1979 |access-date=20 December 2018}} Search for Accession Number PB295070</ref>  Ironically, Breda would later construct light rail cars that would replace the SLRV's in both San Francisco and Boston (see ''[[#Replacements and retirement|Replacements and retirement]]'' section). [[SEPTA]] of [[Philadelphia, Pennsylvania]] was initially interested (especially because the SLRV would be locally produced), but purchased custom LRVs from [[Kawasaki Heavy Industries Rolling Stock Company|Kawasaki]] because the US SLRV would not clear the [[13th Street station (SEPTA)|City Hall loop]].<ref name=rollsign198203 /> SEPTA tailored the bid by specifying the vehicle width to be {{convert|4|in|4=0|abbr=on}} narrower than the SLRV specification to exclude it from consideration.<ref name=TX-1980/>{{rp|95}} The [[SEPTA K-car | Kawasaki cars]] for SEPTA were assembled at the Boeing Vertol plant to meet "Buy America" requirements.<ref name=RA-1980 />

While [[Pittsburgh Light Rail|Pittsburgh]], [[Streetcars in New Orleans|New Orleans]], and [[Newark Light Rail|Newark]] collaborated with UMTA in designing the SLRV{{Citation needed|date=August 2023}}, and already had traditional streetcars, they ultimately did not buy the cars, nor would any newly built light rail systems such as [[San Diego Trolley|San Diego]].  Pittsburgh converted their legacy low-entry streetcar system into dual-entry light rail, in a similar fashion to San Francisco's Muni Metro, and bought (at the time) custom [[Siemens SD-400 and SD-460|Siemens SD-400]] light rail cars, these being derived from the [[Siemens–Duewag U2]] design originally built for the [[Frankfurt U-Bahn]] and later adapted for the newly built light rail systems in San Diego, [[Edmonton LRT|Edmonton]], and [[Calgary Transit|Calgary]]. Newark would continue to operate PCC's until 2001, when they were replaced with new low-floor LRV's built by [[Kinki Sharyo]] vehicles.<ref>{{cite web
| url = http://www.njtransit.com/nn_press_release.jsp?PRESS_RELEASE_ID=326
| title = "NEW" NEWARK CITY SUBWAY DEBUTS - Smooth, Air-Conditioned Light Rail Vehicles Carry Customers in 21st Century Comfort
| author = Klufas, Michael| access-date = September 6, 2015 | date = August 27, 2001| publisher = NJ Transit
| archive-url = https://web.archive.org/web/20070927233956/http://www.njtransit.com/nn_press_release.jsp?PRESS_RELEASE_ID=326
| archive-date = September 27, 2007
}} Press Release 326.</ref>  New Orleans, which had never adopted the PCC design, continues to operate its 1920's vintage [[Perley Thomas]]-built streetcars, supplemented by modernized custom-built replicas of the cars.  All subsequent newly built light rail systems have likewise bought customized equipment from Siemens, Kinki Sharyo, Breda, and other builders that have since entered the US light rail market.

The US SLRV design also influenced the early design of the [[Canadian Light Rail Vehicle]].<ref name=rollsign198203>{{cite magazine |title=LRV's in Boston: The Road Back |pages=11–12 |magazine=Rollsign |date=March–April 1982 |first=George |last=Chiasson |publisher=Boston Street Railway Association}}</ref>

{| class="wikitable" style="text-align:center"
! Operator || Year Built || Fleet Series || Quantity || Year of retirement || Notes
|-
| rowspan=2 | [[Massachusetts Bay Transportation Authority|MBTA]]<br/>[[File:MBTA.svg|35px]] || 1976–78 || 3400–3534 || rowspan=2 | 144 || rowspan=2 | 1987–2007 || style="text-align:left;font-size:90%;" | 3417, 3448, and 3453 were converted to [[maintenance of way]] equipment. 3424 was sent to [[Seashore Trolley Museum]] in 2009.<ref name=MBTA-roster>{{cite web |url=http://transithistory.org/roster/ |title=The MBTA Vehicle Inventory Page |publisher=Transit History |access-date=19 December 2018}}</ref>
|-
| 1977{{citation needed|date=June 2019}} || 3535–3543 || style="text-align:left;font-size:90%;" | Part of the initially rejected option of 40; 31 of these were later delivered to Muni and 9 were delivered to MBTA in 1983. 3541 was sent to the U.S. Army in 2000.<ref name=MBTA-roster />
|-
| rowspan="2" | [[San Francisco Municipal Railway|Muni]] (LRV1)<br/>[[File:Muni worm logo.svg|50px]] || 1978 || 1200–1299 || rowspan="2" | 131 || rowspan="2" | 1996–2001 || style="text-align:left;font-size:90%;" | Two prototype cars were delivered in October 1977, numbered 1220–1221; they were later renumbered 1212–1213.<ref>{{cite magazine |last=Jewell |first=Don |title=Muni's First LRVs |date=November 1977 |magazine=[[Pacific RailNews|Pacific News]] |page=14 |url=http://magazine.trainlife.com/wp-content/uploads/2017/08/pne_197711.pdf |archive-url=https://web.archive.org/web/20220721073857/http://magazine.trainlife.com/wp-content/uploads/2017/08/pne_197711.pdf|archive-date=July 21, 2022 |url-status=dead |issn=0030-879X}}</ref><ref name=mckane-perles1982>{{cite book |last1=McKane |first1=John |last2=Perles |first2=Anthony |title=Inside Muni: The Properties and Operations of the Municipal Railway of San Francisco |year=1982 |publisher=[[Interurban Press]] |location=Glendale, CA (US) |pages=47, 56 |isbn=0-916374-49-1}}</ref> 1222 and 1252 were damaged during subway testing on Nov 12, 1979; these cars were scrapped for parts, which were used to finish ex-MBTA 3565, renumbered to Muni 1252 (II) and delivered on Jan 27, 1982.<ref name=Perles-84>{{cite book |title=Tours of Discovery: A San Francisco Muni Album |page=125 |chapter=8: Muni up to Date |author=Perles, Anthony |date=Fall 1984 |publisher=[[Interurban Press]] |isbn=0-916374-60-2 |location=Glendale, California}}</ref> 1212 wrecked into 1255 at the Van Ness junction in the Muni Metro subway in 1987. The good halves were converted into a new 1255 and the bad halves were scrapped in February 1994.
|-
| 1977{{citation needed|date=June 2019}} || 1300–1329 || style="text-align:left;font-size:90%;"|31 cars in total. The first car from the rejected MBTA lot (ex-3565) was procured to replace two wrecked cars from the original order of 100 and reassigned number 1252.<ref name=Perles-84/> The other 30 ex-MBTA cars were numbered 1300–1329 and entered service in 1981–1984. 
|}

===Issues===
{{quote box |text=They work, but they just don't work as well as they should. Practically every part in the car is a brand new design. Everyone said the technology would work, but it hasn't. |author=Kenneth Campbell, MBTA |source=1978 interview<ref name=SFE-781207 /> |width=25em}}
Before they were delivered, Boeing claimed the US SLRV would be reliable and virtually maintenance-free.<ref name=PopSci76 /> From their earliest days of service, however, the SLRVs proved to be a major financial and mechanical nightmare. After the initial three months of service, the MBTA was forced to halt all light rail service on April 16, 1977, for nine or ten days due to equipment unavailability.<ref name=H6227/>{{rp|19}}<ref name=Boston-1980/> The MBTA was unable to retire their PCCs; instead, MBTA instituted a PCC rebuilding program to augment the SLRV fleet and maintain Green Line service. In San Francisco, the [[#Problems|problems with the SLRVs]] led to the Muni Metro not reaching its full potential until 1982.<ref name="TheyKnewAboutIt" /><ref name="BoeingsForScrapOrSale!" />

According to the original design specification, the goals for [[mean time between failures]] were set at 1,400 hours or {{convert|21000|mi||-3}} for the propulsion and auxiliary electric systems, which assumes average operating speeds of {{convert|15|mph|kph}}; 1,500 hours or {{convert|22500|mi||-2}} for door and step systems; and 4,000 hours or {{convert|60000|mi||-3}} for the friction brakes.<ref>{{cite web |url=https://ntrl.ntis.gov/NTRL/ |title=Standard Light Rail Vehicle Specification, Technical Specification |publisher=National Technical Information Service |author=Urban Mass Transportation Administration, US Department of Transportation |date=1972 |access-date=20 December 2018}} Search for Accession Number PB220748</ref>{{rp|2–19}} In comparison, for 1982, Muni SLRVs were breaking down an average of every {{convert|600|mi||-1}} (40 hours at {{cvt|15|mph|kph}} operating speeds); reliability rose to {{cvt|1800 to 2000|mi||-2}} (120–133 hours) between failures by 1988, but this was still a failure rate almost 15 times the frequency of the {{convert|28300|mi||-2}} (1,890 hours) MTBF for the [[Siemens–Duewag U2]] used in the [[San Diego Trolley]] system.<ref name="TheyKnewAboutIt" />

[[File:SLRV Engineering Fig 1-2 (1979).jpg|thumb|right|Interior of Muni car, looking towards end from near articulated section. Note resilient seating.]]
In Boston, the MBTA was accepting new cars from Boeing-Vertol, but the cars were falling out of service faster than the MBTA's maintenance staff could repair them. In addition, the MBTA could not acquire replacement parts fast enough to repair the disabled SLRVs. In a desperate effort to keep as many SLRVs operating as possible, MBTA set aside 35 disabled cars to be cannibalized for replacement parts.<ref name=SFE-781207>{{cite news |url=https://www.newspapers.com/newspage/460621571/ |title=A hard look / The Toonerville trolley of space-age San Francisco |author=Hollis, Robert |date=December 7, 1978 |newspaper=San Francisco Examiner |access-date=25 December 2018}}{{subscription required}}</ref>

To help prevent the riding public from seeing the number of brand-new, but heavily cannibalized SLRVs, several of the cars were hidden around the system where the public was not likely to find them. A major newspaper story emerged when a reporter and a photographer managed to get into a section of the Green Line's subway which was not in use at the time and found it was full of cannibalized cars which had been abandoned in the tunnel.{{citation needed|date=May 2018}} The MBTA had been towing the cars into the subway during the middle of the night when the subway was closed to the public. The story and photographs brought the problems with the SLRV into the public eye for the first time. After the story broke, out-of-service SLRVs began to appear in several storage yards which were easily viewed by the public, though this may have simply been due to the ever-increasing number of disabled cars.{{citation needed|date=May 2018}}

MBTA purchased $2.2&nbsp;million in spare parts in May 1978 to alleviate further issues, and Muni purchased $1.5&nbsp;million in parts, forewarned by the MBTA experience. Muni also requested to add 200 employees in order to maintain and run the new SLRVs.<ref name=SFE-781207 /> Shipments of US SLRVs to MBTA were suspended in June 1978 after 135 cars had been delivered due to ongoing issues,<ref name=Boston-1980/> and MBTA prepared the 35 cannibalized cars for return to Boeing later that year.<ref name=SFE-781207 /> On October 9, 1978, MBTA rejected the final 40 SLRVs and directed Boeing-Vertol to retrieve the 35 cannibalized cars, concluding that poor fleet reliability meant that Boeing was in breach of warranty.<ref name=H6227/>{{rp|6;19}} By 1978, the first five cars had been delivered to Muni; those had already underwent three rounds of modifications based on the MBTA experience.<ref name=SFE-781207 />

===Settlement===
On December 15, 1978, MBTA and Boeing signed an agreement that revised specifications to enable the full delivery of 175 SLRVs,<ref name=H6227/>{{rp|20}} but reliability issues continued through 1979. An independent commission recommended that MBTA reorganize its LRV program and take quick action to resolve those issues.<ref name=H6227/>{{rp|6}} The SLRV fleet availability typically was less than 50% of the total number of cars on the property for the first few years of service; during the second and third quarters of 1979, Green Line trains missed 12,201 weekday trips, a 184% increase over the 6,598 missed weekday trips over the same period in 1978.<ref name=Boston-1980/> In May 1979, MBTA and Boeing signed an agreement to modify and refurbish the 35 cannibalized SLRVs,<ref name=H6227/>{{rp|20}} but MBTA maintenance workers threatened to strike after MBTA ordered Boeing to retrieve the SLRVs, demanding the work be conducted in MBTA shops; Boeing stated in July that it would not accept any more SLRVs from Boston (three had already been returned) until the labor dispute had been resolved.<ref name=H6227/>{{rp|6;20}} MBTA, Muni, and Boeing began to meet during the summer of 1979 to determine who would be responsible for resolving the identified problems.<ref name=GAO-MBTA-80/> Boeing made an offer in September 1979 which identified specific design issues that would be corrected at its expense, including leaking gearboxes, air conditioning compressor issues, and traction motor failures, but MBTA rejected the offer; around this time, MBTA hired product liability attorney and law professor [[William Schwartz (law professor)|William Schwartz]] to negotiate on its behalf<ref name=GAO-MBTA-80/><ref>{{cite news |url=https://newspaperarchive.com/lowell-sun-apr-04-1980-p-58/ |title=Lawyer defends $799,000 fee for settling an MBTA case |date=April 4, 1980 |newspaper=Lowell Sun |access-date=23 December 2018}}{{subscription required}}</ref> in August 1979.<ref name=H6227>{{cite report |url=https://student.nesl.edu/research/Legislative_Council/H6227_boeing.pdf |title=Special Report of the Committee on Transportation relative to the Hiring of Attorney William Schwartz by the Massachusetts Bay Transportation Authority and the Settlement Between Said Authority and Boeing-Vertol, Inc. (under House order No. 3874 of 1980) |date=April 17, 1980 |author=Joint Legislative Committee on Transportation |publisher=The Commonwealth of Massachusetts |access-date=3 January 2019}}</ref>{{rp|7;21}}

Boeing took the position that issues had been caused by poor maintenance, poor track conditions, driver errors, and cannibalization.<ref name=H6227 />{{rp|33}} Schwartz argued that availability of the SLRV was less than 90% and had cost MBTA between $75–100&nbsp;million to that point.<ref name=H6227 />{{rp|39}} On November 19, 1979, MBTA and Boeing reached a settlement; in order to make up for financial losses due to equipment unavailability, Boeing-Vertol would return $40&nbsp;million to MBTA for the cost of repairs and modifications to several cars. In addition, the MBTA was allowed to reject delivery of the 40 cars remaining from the amended 175-car order.<ref name=GAO-MBTA-80/><ref name="TheyKnewAboutIt" /> At the time of the settlement, 41 of MBTA's 135 SLRVs were inoperable due to design issues, accidents, and/or cannibalization for parts, which would require an estimated {{USD|15600000|1979|round=-4}} to restore to operating condition.<ref name=GAO-MBTA-80 /> Under the terms of the settlement, all warranties were terminated, and any further repairs would be the responsibility of MBTA, not Boeing, although Boeing would deliver modification kits to MBTA, whose maintenance personnel would install them at MBTA's expense to correct the previously identified issues. Boeing would only warranty the kits for defects in the parts; if they did not resolve the issues, MBTA would be responsible for the cost of redesign as well.<ref name=GAO-MBTA-80 /> The size of Schwartz's fee for negotiating the settlement, {{USD|799000|1979|round=-3}}, prompted an investigation by the Massachusetts legislature.<ref name=H6227 />

===Final deliveries===
The 40 rejected MBTA cars sat in storage at Boeing-Vertol's plant for a short time, until San Francisco's Muni purchased some of these cars at a steep discount. The first of the "Boston" cars which Muni purchased was to replace two SLRVs which had been damaged during preservice Muni Metro subway testing in 1979 and were deemed beyond economic repair.<ref name=Perles-84 /> After the successful conversion of that first car, Muni ordered an additional 30 SLRVs from the rejected Boston units to further bolster their fleet. The "Boston" cars in San Francisco were modified to meet the needs of the Muni Metro, but were easily distinguished by the wood grain interior finish at the operator's cab and articulation section,<ref>{{cite web |url=http://world.nycsubway.org/perl/show?16573 |title=Image 16573: Interior of a MBTA Boeing |author=Haas, Eric |date=November 23, 1999 |website=NYC Subway |access-date=December 19, 2018}}</ref> which did not match the yellowish orange color (from the [[Walter Landor]]-designed "sunset" livery) on the cars delivered under the original Muni order of 100.<ref>{{cite web |url=http://www.trainweb.org/oerhs/roster/photos/muni1213-int-04.jpg |title=Interior of an original Muni Boeing |website=Trainweb |archive-url=https://web.archive.org/web/20010905100509/http://www.trainweb.org/oerhs/roster/photos/muni1213-int-04.jpg |archive-date=September 5, 2001 |url-status=dead}}</ref>

By 1980, Boeing was no longer marketing the SLRV.<ref name=TX-1980/>{{rp|107}}<ref name=RA-1980>{{cite magazine |url=http://digitalcollections.library.cmu.edu/awweb/awarchive?type=file&item=478001 |title=Competing for the light-rail vehicle market |author=Middleton, William D. |date=September 29, 1980 |magazine=Railway Age |pages=56–60 |access-date=26 December 2018}}</ref> In 1983 the last SLRVs at Boeing-Vertol's facility were delivered when the MBTA accepted nine remaining cars (3535–3543) from the group of 40 that MBTA had previously rejected. MBTA also took delivery of five cannibalized "shells" in 1983; these had been delivered to MBTA in the 1970s, but were subsequently returned to Boeing in 1979.<ref name=MBTA-roster /> The title for these five cars reverted to Boeing because MBTA did not respond promptly under the terms of the 1979 settlement, and had been scrapped to supply parts in the meantime.<ref name=H6227/>{{rp|9}} The five "shells" were scrapped in 1988.<ref name=MBTA-roster />
{|class="wikitable floatright" style="font-size:85%;text-align:center;width=35em"
|+SLRV compared to key competitors<ref name=LRT-StateArt76>{{cite report |url=https://catalog.hathitrust.org/Record/005467247 |title=Light Rail Transit: A State of the Art Review |date=Spring 1976 |publisher=Urban Mass Transportation Administration, US Department of Transportation |author=Diamant, E.S. |access-date=20 December 2018}}</ref>{{rp|136}}
|-
! &nbsp; !! Boeing<br/>SLRV !! [[Siemens–Duewag U2|Düwag U2]] !! [[PCC streetcar|PCC]] !! [[Canadian Light Rail Vehicle|CLRV]] !! Buffalo<br/>LRV<ref name=Buffalo-LRV/>
|-
! Axles/<br/>articulation
| 6/1 || 6/1 || 4/0 || 4/0 || 4/0
|-
! Length
| {{convert|71.5|ft|m|abbr=on|disp=br}} || {{convert|75.5|ft|m|abbr=on|disp=br}} || {{convert|43.5|to|50.5|ft|m|abbr=on|disp=br}} || {{convert|50.67|ft|m|abbr=on|disp=br}} || {{convert|66.8|ft|m|abbr=on|disp=br}}
|-
! Width
| {{convert|8.85|ft|m|abbr=on|disp=br}} || {{convert|8.70|ft|m|abbr=on|disp=br}} || {{convert|8.33|to|9.0|ft|m|abbr=on|disp=br}} || {{convert|8.50|ft|m|abbr=on|disp=br}} || {{convert|8.58|ft|m|abbr=on|disp=br}}
|-
! Height
| {{convert|11.5|ft|m|abbr=on|disp=br}} || {{convert|10.8|ft|m|abbr=on|disp=br}} || {{convert|10.1|ft|m|abbr=on|disp=br}} || {{convert|11.0|ft|m|abbr=on|disp=br}} || {{convert|12.3|ft|m|abbr=on|disp=br}}
|-
! Floor<br/>height
| {{convert|2.82|ft|m|abbr=on|disp=br}} || {{convert|3.18|ft|m|abbr=on|disp=br}} || {{convert|2.75|ft|m|abbr=on|disp=br}} || {{convert|3.02|ft|m|abbr=on|disp=br}} || {{convert|3.07|ft|m|abbr=on|disp=br}}
|-
! Weight<br/>(empty)
| {{convert|68000|lb|abbr=on|disp=br}} || {{convert|66000|lb|abbr=on|disp=br}} || {{convert|33000|to|42000|lb|abbr=on|disp=br}} || {{convert|52000|lb|abbr=on|disp=br}} || {{convert|70000|lb|abbr=on|disp=br}}
|-
! Seats
| up to 68 || 64 || 49 to 69 || 42 or 47 || 51
|-
! Minimum<br/>curve radius
| {{convert|32|to|42|ft|m|abbr=on|disp=br}} || {{convert|82|ft|m|abbr=on|disp=br}} || approx. {{convert|40|ft|m|abbr=on|disp=br}} || {{convert|38|ft|m|abbr=on|disp=br}} || unk.
|-
! Acceleration
| {{convert|4.1|ft/s2|abbr=on|disp=br}} || {{convert|3.3|ft/s2|abbr=on|disp=br}} || {{convert|4.6|ft/s2|abbr=on|disp=br}} || {{convert|4.6|ft/s2|abbr=on|disp=br}} || {{convert|4.2|ft/s2|abbr=on|disp=br}}
|-
! Deceleration
| {{convert|5.1|ft/s2|abbr=on|disp=br}} || {{convert|3.9|ft/s2|abbr=on|disp=br}} || {{convert|4.6|ft/s2|abbr=on|disp=br}} || {{convert|5.1|ft/s2|abbr=on|disp=br}} || {{convert|4.4|ft/s2|abbr=on|disp=br}}
|-
! Emergency<br/>deceleration
| {{convert|8.8|ft/s2|abbr=on|disp=br}} || {{convert|10|ft/s2|abbr=on|disp=br}} || {{convert|9.5|ft/s2|abbr=on|disp=br}} || {{convert|10|ft/s2|abbr=on|disp=br}} || {{convert|6.4|ft/s2|abbr=on|disp=br}}
|}

== Design ==

[[File:US Standard Light Rail Vehicle plan.svg|thumb|right|upright=2.5|SLRV outline and dimensions]]

The SLRV is a double-ended high-floor articulated light rail vehicle {{convert|71|ft|m|abbr=on}} long overall (over the anticlimbers), in the same range as many heavy rail vehicles both at the time and now, but noticeably shorter than many other modern LRVs such as the at-minimum-{{Convert|81|ft|adj=on}} [[Siemens S700 and S70|Siemens S70 and S700]] commonly found today, which rides on three two-axle trucks (six axles in total). The two end trucks are spaced {{convert|13|ft|6|in|m|abbr=on}} from each end (couplers included) and {{convert|23|ft|m|abbr=on}} from the center truck under the articulated section, allowing a minimum track radius of {{convert|32|ft|m|abbr=on}}.<ref name=SLRV-I /> The dimensions of the SLRV were determined by the existing track constraints of three proposed operators: MBTA (Boston), Muni (San Francisco), and SEPTA (Philadelphia).<ref name=LRT-StateArt76/>{{rp|144}} Each car has an "A" and "B" end separated by a central articulated section. Each side has three passenger doors {{convert|53|in|mm|abbr=on}} wide: one near the operator's cab, and two straddling the articulated section; there is no door at the rear (trailing) cab (in the direction of travel).<ref name=SLRV-I /> The tested empty weight of the vehicle (including {{convert|1770|lb|abbr=on}} of instrumentation) was {{convert|69130|lb|abbr=on}}; for a normal load of 100 passengers, the vehicle was {{convert|82500|lb|abbr=on}} and for the crush load of 219 passengers, the vehicle was {{convert|104495|lb|abbr=on}}.<ref name=SLRV-I />

Each end truck carries a single DC motor which powers both axles and has a rated output of {{convert|210|hp|kW|abbr=on}} at 1135 RPM, operating on 285 VDC; the traction motor drives the wheels through a reduction gear set of 5.571:1.<ref name=SLRV-I /> In the original 1971 LTK design for Muni, the center truck was also powered, giving a top speed of {{convert|65|mph|kph|abbr=on}};<ref name=TX-1980/>{{rp|220}} in the final SLRV specification, the center truck was not powered and the top speed was reduced to {{convert|50|mph|kph|abbr=on}}.<ref name=SLRV-I /> Power to the traction motors is controlled through a solid state [[Chopper (electronics)|"chopper" circuit]] operating at a frequency ranging between 0 to 400&nbsp;Hz for vehicle speeds up to {{convert|17|mph|kph|abbr=on}}, allowing a continuously variable control of power from the 600&nbsp;V overhead lines rather than the traditional trolley control at the time, which used a varied number of discrete resistances to control motor current.<ref name=PopSci76 /><ref name=LRT-StateArt76/>{{rp|134}} Above {{convert|17|mph|kph|abbr=on}}, the power is not "chopped" and is instead applied directly to the traction motors.<ref name=Bei-78>{{cite journal |url=http://onlinepubs.trb.org/Onlinepubs/sr/sr182/182-004.pdf |title=San Francisco's Muni Metro, A Light-Rail Transit System |author=Bei, Rino |date=1978 |journal=Light Rail Transit: Planning and Technology |volume=182 |pages=18–23 |publisher=Transportation Research Board |access-date=26 December 2018}}</ref>

Primary dynamic braking is accomplished by running the traction motors as generators and dissipating the electricity generated through two brake resistor grids; a friction brake consisting of a single inboard disc brake per axle is blended with the dynamic braking as needed. The friction brake alone is sufficient to hold a fully loaded SLRV (with 219 passengers) on a 9° slope.<ref name=SLRV-I /> In addition, six electromagnetic [[track brake]]s are provided; on the Muni cars, the track brakes are controlled independently to hold the car in place when starting on a slope, and on the MBTA cars, the track brakes are blended into the main brakes.<ref name=SLRV-I /> Dynamic braking was enabled by using a separate power source to energize the field coils on the traction motors; Boeing stated that [[regenerative braking]] was possible. Although regenerative braking was not implemented on the SLRV, it was enabled on the similar CLRV.<ref name=PopSci76 />

[[File:MBTA 3424 at Seashore Trolley Museum 405 (37559477741).jpg|thumb|right|upright=2.0|MBTA #3424 at [[Seashore Trolley Museum]] (2017), as rebuilt in 1997 to add roof-mounted air conditioning units on each end and bifold doors (3 per side).]]
The articulated section allows up to 16° of rotation in the horizontal plane, 3° of vertical sag (center section lower than ends), and 4.3° of vertical crest (center section higher than ends),<ref name=UMTA-NALRV /> which permits the SLRV to traverse curves as sharp as {{convert|42|ft|abbr=on}} inside radius, travel through valleys with a vertical curvature of {{convert|460|ft|abbr=on}}, and crest hills with a vertical curvature of {{convert|310|ft|abbr=on}}.<ref name=SR161-PATC>{{cite conference |url=http://onlinepubs.trb.org/Onlinepubs/sr/sr161/sr161-005.pdf |title=Physical, Operational, and Performance Characteristics of the Light Rail Mode |author=Vigrass, J. William |date=June 1975 |location=Philadelphia |conference=National Conference on Light Rail Transit |publisher=Transportation Research Board |pages=19–25 |access-date=26 December 2018}}</ref>

The SLRV rolls on lightweight Acousta Flex composite resilient wheels {{convert|26|in|mm|abbr=on}} in diameter; these wheels use aluminum hubs separated from the steel rims/tires by a silicone rubber cushion.<ref name=SLRV-I /><ref>{{cite magazine |url=https://books.google.com/books?id=uRAgliO29ZwC&pg=PA75 |title=Squeal squelcher |date=August 1974 |page=75 |magazine=Popular Science |access-date=27 December 2018}}</ref> The cushion is {{convert|3/16|in|abbr=on}} thick and is injected in the threaded space between the rim and hub; the design was developed by Standard Steel and [[BART]] in the 1960s.<ref>{{cite report |url=https://www.bart.gov/sites/default/files/docs/noisereport.pdf |title=TCRP Report 23: Wheel/Rail Noise Control Manual |author=Nelson, James T. |date=1997 |isbn=0-309-06060-5 |publisher=Transportation Research Board |access-date=27 December 2018}}</ref>{{rp|111}} The resilient wheels reduce squeal when negotiating tight curves.<ref name=SLRV-I /> Interior noise was claimed to be 65&nbsp;dB. The design of the trucks is adapted from the Japanese [[Shinkansen]] trains.<ref name=PopSci76 /> The trucks are equipped with rubber chevron springs and pneumatic suspension, which automatically adjusts to maintain floor height with varying loads. Damping is accomplished by both hydraulic (lateral) and pneumatic (vertical) means.<ref name=SLRV-I />

[[File:Buffalo Metro Rail train at Erie Canal Harbor station, August 1988.jpg|thumb|left|upright|[[Buffalo Metro Rail]] LRV by Tokyu (1988)]]
The car body shells and truck frames were built by [[Tokyu Car Corporation]] in [[Yokohama]] and the motors provided by [[Garrett AiResearch|Garrett]], with assembly at the Boeing plant in [[Ridley Park]], [[Pennsylvania]]. After production was ended by Boeing, Tokyu Car Corporation built light rail cars for [[Buffalo Metro Rail]] which externally resemble the SLRV, but many differences, most noticeably the lack of articulation, use of external steps for low-platform boarding instead of internal steps, and the use of single-leaf pocket doors similar to the [[London Underground D78 Stock|London Underground D Stock]].<ref name=Buffalo-LRV>{{cite conference |url=http://onlinepubs.trb.org/Onlinepubs/sr/sr221/221-030.pdf |conference=National Conference on Light Rail Transit |publisher=Transportation Research Board of the National Academy of Sciences |location=San Jose, California |date=May 8–11, 1988 |title=Buffalo's Light Rail Vehicle |author=Antonio Jr., Ben J. |access-date=17 May 2019}}</ref>

===Differences===
{|class="wikitable floatright" style="font-size:85%;text-align:center;width=45em"
|+SLRV differences<ref name=SLRV-I/>{{rp|1–5}}
|-
! &nbsp; !! MBTA !! Muni
|-
! Seats
| 52{{efn|Later reduced to 48}} || 68
|-
! Cab Signalling
| {{no}} || {{yes}}
|-
! Steps
| Fixed{{efn|Allows street level boarding}} || Convertible{{efn|Convertible steps on the four center doors only}}{{efn|Allows boarding from high platforms and at street level}}
|-
! Overspeed Control
| {{yes}}{{efn|{{convert|52|mph|kph|abbr=on}} limit}} || {{no}}
|-
! Destination Signs
| Manual || Automatic
|-
! Air Conditioning
| {{yes}}{{efn|Single blower speed}} || {{no}}{{efn|Three blower speeds}}
|-
! [[Track brake]]s
| Blended || Independent
|-
! Wheel Tread Contour
| 1:40 || 1:20
|-
|colspan=3 | '''Notes'''<br/>{{notelist|20em}}
|}
While Boston and San Francisco bought their cars at the same time and they appear identical externally, the cars have differences:

*Doors: The doors themselves, at first, were essentially the same. However, Muni's cars had moveable steps at the four center doors (those nearest the articulated section), which could be lowered for street-level boarding or raised for boarding from high-level platforms, such as those in the subway. The Boston cars did not have this feature and so must be boarded from street-level. The doors were designed to accommodate both types of stairs.<ref name=Bei-78 /> These doors proved troublesome and the MBTA eventually replaced them with bi-folding doors, further distinguishing them from Muni's.
*Appliances: The MBTA SLRVs were fitted with air-conditioning units for Boston's humid climate. Due to San Francisco's relatively mild climate, the Muni SLRVs were provided with forced-air ventilation instead of air conditioning. The air conditioning units that the Boston cars were delivered with had problems such as sucking up dust and other debris from the subway tunnels and were later replaced with roof-mounted Sutrak air conditioners in the late-1980s to mid-1990s.
*Interior styling: The "Boston" cars featured wood grain interior finishes at the operator's cab and articulation section, while Muni cars had a yellowish-orange color interior. However, certain Muni SLRVs (numbered 1252 and 13xx) actually had the same wood grain interior finish as Boston's because those cars were originally built for Boston, who rejected and returned them to Boeing. Muni then bought these cars, had their air-conditioners removed and fitted them with all the features exclusive to its fleet. The wood grain in these cars is thus the only feature that distinguishes these cars from those originally made for Muni.
*Automation: Muni cars were equipped with cab signaling to enable automated operation through the Market Street subway with planned headways as low as 60 seconds.<ref name=SR161-PATC />
*Seating: The San Francisco cars originally had cushioned seats, but they were replaced with hard plastic seats in 1985, because of vandalism.<ref>''[[Modern Tramway]]'', April 1985, p. 140.  [[Ian Allan Publishing]].</ref>
*Capacity: San Francisco's cars seated 68, while the Boston cars seated 52 until the MBTA later had four seats removed to better accommodate wheelchairs.

[[File:Boeing USSLRV (MBTA 3523).jpg|thumb|right|Boeing Vertol US SLRV #3523 in service for the [[Massachusetts Bay Transportation Authority|MBTA]] on the [[Green Line C branch]], bound for Cleveland Circle, in 2005. This view shows the roof-mounted air-conditioning units and bi-fold doors added by MBTA in place of the original equipment. MBTA's last Boeing cars were retired in March 2007.]]

== Problems ==
One of the largest issues was simply that the Boeing SLRV was a "compromise" car. Both Boston and San Francisco had very different needs for the SLRV: Boston needing a more traditional streetcar, while San Francisco needed a more specialized car for its Muni Metro subway.<ref name="TheyKnewAboutIt" /> Because the San Francisco cars would use station platforms at both street level (surface stations) and high level (underground), the vehicle steps needed to switch between the two modes. This became a passenger flow problem since the Muni cars could only use the two center doors on the SLRVs in the subway: the front end of the car curved away from the high-level platforms too much to allow passengers to safely board or alight the cars.<ref name=Straus-78>{{cite journal |url=http://onlinepubs.trb.org/Onlinepubs/sr/sr182/182-009.pdf |title=Light-Rail Transit: Less Can Mean More |author=Straus, Peter |date=1978 |journal=Light Rail Transit: Planning and Technology |volume=182 |pages=44–49 |publisher=Transportation Research Board |access-date=26 December 2018}}</ref> The narrow front end, in turn, was required by Boston so the SLRV could navigate the tight curves in the MBTA's 1897-vintage subway.

Professor [[Seymour Melman]] partially blamed the use of a longtime defense contractor. Boeing Vertol's customary client (US Department of Defense) was relatively budget insensitive, more tolerant of cost overruns, and had sufficient funding and workforce to conduct complex maintenance, all contrary to the needs and abilities of a municipal transit agency.<ref name=Melman-79/> The design team primarily had experience in aerospace design, not rail vehicles,<ref name=Ueda>{{cite web |url=http://www.kinkisharyo.co.jp/pdf/gihou/KSW15/KSW15_e_P04-05.pdf |title=Massachusetts Bay Transportation Authority |author=Ueda, Shigehiro |publisher=Kinki Sharyo |access-date=26 December 2018}}</ref> did not make a serious effort to gain that experience, and did not design for ease of maintenance. In some cases, portions of the SLRV had to be disassembled by acetylene torch to access components.<ref name=Melman-79 />

Boeing marketed the SLRV as a system and took the role of an integrator, subcontracting the design and fabrication of major components to external suppliers from places as far as Germany, Japan, and the United Kingdom. This approach created uncertainty in component delivery dates and essentially precluded prototype testing in favor of meeting contracted schedule milestones, turning MBTA and Muni into, effectively, beta testers for the SLRV.<ref name=Melman-79>{{cite speech |url=https://ewh.ieee.org/soc/ssit/Newsletter%20Archive/1972-1981/TS7-26-79.pdf |title=Engineering Job Stability and Economic Conversion |author=Melman, Seymour |date=May 17, 1979 |publisher=IEEE, Long Island Section |access-date=25 December 2018}}</ref> Because no prototype testing was conducted prior to vehicle delivery, the appropriate identification and stock levels of spare parts could not be established before delivery, and MBTA was forced to cannibalize SLRVs for parts to maintain fleet availability during the early years of operation.<ref name=Melman-79 />

Other specific problems with the SLRV include but are not limited to:
*[[Derailment]]s on tight curves,<ref name=Boston-1980>{{cite magazine |url=https://www.bostonmagazine.com/news/1980/01/01/boston-mbta-problems/2/ |title=Boston 'T' Troubles |author=Oglesby, Carl |date=January 1980 |magazine=Boston |access-date=19 December 2018}}</ref> which would seriously damage the car's articulation section, itself problematic as Boeing designed its own articulated section so as to avoid obtaining a license from overseas builders such as [[Duewag]].{{citation needed|date=May 2018}}
*Another major problem was the shorting of electrical systems and premature failures in the car's motors and propulsion systems. Boeing used a relatively advanced [[Chopper (electronics)|chopper]] control system for the cars as insisted by the federal government. While such systems have been implemented successfully in many subway, light rail and trolley bus systems, the systems installed in Boeing's cars were found to be overly complicated for the transit systems' use.{{citation needed|date=May 2018}} It is however unclear how problematic this was as chopper control did prove to be commonplace in the United States into the early 1990s.
*The SLRVs came equipped with overly complex [[plug door]]s, which were originally intended to accommodate high-platform operation for Muni in the [[Market Street subway]]. Boeing established a requirement to have the doors automatically reopen if an obstruction was encountered while closing in order to avoid crushing passengers;<ref name=LRT-StateArt76/>{{rp|146}} the firm initially charged with designing the doors successfully met this requirement, but made the doors too sensitive: the doors would recycle upon closing, as it detected a normal closure as an obstruction and would recycle the doors. Boeing hired another subcontractor to redesign the doors, stipulating that fewer components should be used.<ref name=Melman-79 /> These doors would frequently short circuit and caused a significant nuisance for the MBTA. The transit agency later attempted to correct the issues with the plug doors by adding a wider rubber strip and eliminating the recycling circuit, but the issue was not fully resolved until the mid-1990s, when MBTA retrofitted all Boeings with much more reliable bi-fold doors.<ref name="BoeingsForScrapOrSale!" />
*The corrosion of car shells was another major issue. Cars are constructed primarily of low-alloy, high-tensile steel except for a stainless steel roof panel.<ref name=UMTA-NALRV /> As both Boston and San Francisco are on the ocean, the cars were particularly susceptible to damage from [[sea spray]]. Some cars barely saw a decade of service before being withdrawn due to corroded bodies, as their bodies were shipped from Japan as deck cargo through the Panama Canal and spent a further amount of time sitting outside the Boeing plant near Philadelphia before being assembled and delivered.{{citation needed|date=May 2018}}
*The blended braking system incorporating a single mechanical disk brake on each axle with the resistive brake on the powered trucks was labor-intensive to maintain and unreliable. For the succeeding Type 7 cars delivered by Kinki Sharyo, MBTA chose to use a mechanical-only pneumatic braking system.<ref name=SR221-MBTA>{{cite conference |url=http://onlinepubs.trb.org/Onlinepubs/sr/sr221/221-029.pdf |title=Designing to Fit: The Boston Experience |author=MacKay, Ronald J. |date=May 1988 |location=San Jose, California |conference=National Conference on Light Rail Transit |pages=442–448 |publisher=Transportation Research Board |access-date=26 December 2018}}</ref>
*The Boston cars' air-conditioning units were originally mounted under the car, and constantly sucked in dirt and debris from under the car. The MBTA later modified 76 SLRVs with roof-mounted air-conditioning units to address this.
*The Acousta Flex composite resilient wheels that were originally fitted to the SLRV tended to fail in service and during testing; the bond failed between the elastomer and the wheel rim, which led to the wheel coming apart and also eliminated the electrical path to ground, as conductors were used between the wheel hub and rim. The Acousta Flex wheels were out of production by 1981.<ref>{{cite report |url=https://archive.org/details/wheelrailnoiseco00kurz/page/8 |title=Wheel/Rail Noise Control - A Critical Evaluation |author1=Kurzweil, Leonard G. |author2=Wittig, Larry E. |date=January 1981 |publisher=Urban Mass Transportation Administration, US Department of Transportation |access-date=20 December 2018}}</ref>{{rp|9;11}}

==Replacements and retirement==
[[File:ARetiredBoeingVertolStreetcarAtPharrDivision-2.jpg|thumb|right|Retired [[San Francisco Municipal Railway|Muni]] Boeing Vertol US SLRV #1264 stored at the Duboce Yard in San Francisco in 2007. This car was scrapped in 2016.]]
The problems of the SLRV quickly led their purchasers to look for replacements and supplements to their fleet. Despite improvements, the SLRVs were still proving to be problematic throughout the 1980s, and both cities decided that Boeing cars would not be part of the long-term future of either transit system. The Federal Transportation Administration took an unprecedented step and reduced the economic life of the Boeing SLRV to 15 years<ref name=Cartwright-96>{{cite conference |url=https://trid.trb.org/view/486802 |title=Procurement Strategy Methodologies |author=Cartwright, E |date=June 1996 |conference=Rapid Transit Conference |publisher=American Public Transit Association |access-date=26 December 2018}}</ref> (from "at least 25 years" for trolleys procured using federal assistance),<ref>{{cite web |url=https://www.transit.dot.gov/sites/fta.dot.gov/files/docs/regulations-and-guidance/fta-circulars/58051/5010-1e-circular-award-management-requirements-7-16-18.pdf |title=Circular 5010.1E: Award Management Requirements |date=July 16, 2018 |publisher=Federal Transit Administration |quote=Chapter IV, Section 4, Paragraph f: Minimum Useful Life of Federally Assisted Property<br/>{{pad|1.0em}}(2)c. Trolleys}}</ref> allowing MBTA and Muni to retire the SLRVs early and pursue procurement of replacements by the late 1980s and early 1990s.

Although the SLRV itself was beset by reliability issues and was not successful, Gregory Thompson credits it with making cities aware of light rail transit and defining a modern light rail vehicle.<ref>{{cite conference |url=http://onlinepubs.trb.org/onlinepubs/circulars/ec058/03_01_thompson.pdf |title=Defining an Alternative Future: Birth of the Light Rail Movement in North America |author=Thompson, Gregory L. |date=November 2003 |location=Portland, Oregon |conference=Experience, Economics and Evolution—From Starter Lines to Growing Systems, 9th National Light Rail Transit Conference |publisher=Transportation Research Board |access-date=3 January 2019}}</ref> The successor vehicles in Boston (Kinki Sharyo Type 7) and San Francisco (Breda LRV2/3) closely follow the specifications and performance of the SLRV.

{|class="wikitable" style="font-size:85%;text-align:center"
|+SLRV and successors
|-
! &nbsp; !! Boeing SLRV<ref name=LRT-StateArt76/>{{rp|136}} !! Kinki Sharyo Type 7 (MBTA)<ref name=KS-Type7>{{cite web |url=http://www.kinkisharyo.com/main/wp-content/uploads/2015/08/MBTA.pdf |title=Boston, MA - MBTA (Green Line) Technical Data |publisher=Kinki Sharyo |access-date=2 January 2019}}</ref> !! Breda LRV2/3 (Muni)<ref name=Breda-LRV2>{{cite web |url=http://www.ansaldobredainc.com/images/stories/san_francisco_light_rail.pdf |title=San Francisco LRV |publisher=AnsaldeoBreda |archive-url=https://web.archive.org/web/20150923172341/http://www.ansaldobredainc.com/images/stories/san_francisco_light_rail.pdf |archive-date=September 23, 2015 |url-status=dead}}</ref>
|-
! Axles/<br/>articulation
| colspan=3 | 6/1
|-
! L×W×H{{efn|Length measured over couplers}}
| {{convert|73|×|8.85|×|11.5|ft|m|abbr=on|disp=br}} || {{convert|74|×|8.67|×|11.83|ft|m|abbr=on|disp=br}} || {{convert|75|×|9|×|11.5|ft|m|abbr=on|disp=br}}
|-
! Floor<br/>height
| {{convert|34|in|mm|abbr=on|disp=br}} || {{convert|35|in|mm|abbr=on|disp=br}} || {{convert|34|in|mm|abbr=on|disp=br}}
|-
! Weight<br/>(empty)
| {{convert|68000|lb|abbr=on|disp=br}} || {{convert|85000|lb|abbr=on|disp=br}} || {{convert|79000|lb|abbr=on|disp=br}}
|-
! Motors
| 2×{{convert|160|kW|hp|abbr=on}}<br/>(1 motor/truck) || 4×{{convert|100|kW|hp|abbr=on}}<br/>(2 motors/truck) || 4×{{convert|97|kW|hp|abbr=on}}<br/>(2 motors/truck) 
|-
! Capacity
| 52/68 seated<br/>219 (crush) || 50 seated || 60 seated
|-
! Minimum<br/>curve radius
| {{convert|32|to|42|ft|abbr=on|disp=br}} || {{convert|42|ft|abbr=on|disp=br}} || {{convert|45|ft|abbr=on|disp=br}}
|-
! Acceleration
| {{convert|4.1|ft/s2|abbr=on|disp=br}} || {{convert|1.25|m/s2|ft/s2|abbr=on|disp=br|order=flip}} || {{convert|1.4|m/s2|ft/s2|abbr=on|disp=br|order=flip}}
|-
! Deceleration
| {{convert|5.1|ft/s2|abbr=on|disp=br}} || {{convert|1.56|m/s2|ft/s2|abbr=on|disp=br|order=flip}} || {{convert|1.78|m/s2|ft/s2|abbr=on|disp=br|order=flip}}
|-
! Emergency<br/>deceleration
| {{convert|8.8|ft/s2|abbr=on|disp=br}} || n/a || {{convert|2.66|m/s2|ft/s2|abbr=on|disp=br|order=flip}}
|}

;Notes
{{notelist|25em}}

===MBTA===
After the MBTA terminated their contract with Boeing-Vertol, they were free to make their own modifications to the cars. Several systems were upgraded or improved. Slowly but surely, cannibalized cars were brought into the MBTA shops to be prepped for service.

The MBTA also started "splicing together" damaged cars. Cars 3454 and 3478 had been involved in a high-speed, rear-end collision. The two ends of the cars that made contact were severely damaged. The MBTA's maintenance crews brought the two cars into the shops, and later car 3478 (consisting of 3478A and 3454B) returned to active duty. Car 3454 (consisting of the damaged 3454A and 3478B) was pushed out into the dead storage yard for future disposition. The experience gained in this type of repair laid the ground for several other such cars being returned to revenue service. Eventually, the MBTA's maintenance staff got the active fleet to around 114 cars in the early 1980s.{{Citation needed|date=March 2008}}

[[File:Two trains at Allston Street station, August 2018 (uprighted).jpg|thumb|right|MBTA No. 3699 (left, [[MBTA Kinki Sharyo Type 7|Type 7]]) and No. 3877 (right, [[MBTA AnsaldoBreda Type 8|Type 8]]) at [[Allston Street station]] (August 2018)]]
Between 1986 and 1988 MBTA took delivery of new [[MBTA Kinki Sharyo Type 7|Type 7 light rail car]]s built by [[Kinki Sharyo]], a Japanese railcar builder<ref name=Ueda /> well established within its home country, producing its first railcars for the North American market. These cars have proven to be far more reliable and quickly assumed most of the base service on the Green Line. With the introduction of Type 7s, the MBTA was finally able to retire most of its aging PCC cars, which had to remain in service much longer than originally planned due to the unreliability of the Boeings. In order to make room for the new Kinki Sharyo Type 7 cars, Boston's MBTA instituted its first SLRV scrapping program beginning in 1987. By the end of 1988, nineteen cars had been removed from the property, most of which had been in dead storage since the late 1970s and the remainder were victims of major collisions or derailment damage.{{Citation needed|date=March 2008}} Kinki Sharyo would subsequently go on to produce LRVs for [[DART light rail|Dallas]], [[VTA light rail|San Jose]], [[Valley Metro Rail|Phoenix]], [[Link light rail|Seattle]], and [[Los Angeles Metro Rail|Los Angeles]].

Boston also turned to Breda for a long-term replacement for the Boeings.  While both the Boeings and Type 7 Kinki Sharyo cars have wide door openings and reserved wheelchair spaces that make them compliant with the [[Americans with Disabilities Act of 1990|Americans with Disabilities Act]], Boston's proposed [[MBTA AnsaldoBreda Type 8|Type 8 car]] would have a [[Low-floor tram|portion of its floor lower to the ground]], allowing riders using wheelchairs to board without the need for a lift or mini-high platform.  To help maintain Green Line service until the Type 8s were expected to be in service and to replace Type 7s destroyed in accidents, the MBTA took delivery of an additional 20 Type 7s from Kinki Sharyo in 1997. Additionally, the MBTA contracted with Amerail (formerly [[Morrison Knudsen]]) of Hornell, NY to completely rehabilitate 55 SLRVs in 1996–97 for extended service.<ref>According to NETransit (1999), the rehabilitated units are 3407, 3411, 3413, 3415, 3416, 3420, 3422, 3423, 3424, 3429, 3432, 3437, 3439, 3440, 3441, 3445, 3446, 3447, 3448, 3451, 3457, 3461, 3462, 3468, 3473, 3476, 3477, 3480, 3483, 3485, 3488, 3489, 3490, 3491, 3493, 3495, 3496, 3498, 3499, 3500, 3503, 3510, 3511, 3514, 3515, 3516, 3517, 3520, 3523, 3526, 3530, 3533, 3534, 3535, and 3542.</ref> The SLRV rehab was intended to add an additional three to five years of service to the cars, and included the elimination of the trouble-plagued plug doors in favor of traditional folding doors, and new roof-mounted air-conditioning units.<ref name=NET-1999>{{cite web |url=http://members.aol.com/rtspcc/roster/lr_rost2.html |title=Massachusetts Bay Transportation Authority Boeing LRV Roster |date=1999 |publisher=NETransit |archive-url=https://web.archive.org/web/19991007183745/http://members.aol.com:80/rtspcc/roster/lr_rost2.html |archive-date=7 October 1999 |url-status=dead}}</ref> All of the unrehabilitated MBTA SLRVs were taken out of service after June 27, 1997.<ref name=farewell-3418 />

The MBTA was originally expected to have fully retired their SLRVs around 2001. However, the new Type 8s had been prone to derailing and other technical defects, which had significantly delayed their entry into service, and the MBTA nearly suspended the contract; at that point, the 55 rehabilitated SLRVs were still on the active roster, nearly a third of all Green Line rolling stock.<ref>{{cite report |url=http://web.mit.edu/cron/project/uncertainty/BLUEBOOK/2001%20Revised%20Blue%20Book%20PDF%20Format/2001%20Bluebook%20scanned.pdf#page=9 |title=Ridership and Service Statistics |edition=Eighth |date=2001 |publisher=Massachusetts Bay Transportation Authority |access-date=27 December 2018 |archive-date=March 5, 2016 |archive-url=https://web.archive.org/web/20160305074330/http://web.mit.edu/cron/project/uncertainty/BLUEBOOK/2001%20Revised%20Blue%20Book%20PDF%20Format/2001%20Bluebook%20scanned.pdf#page=9 |url-status=dead }}</ref> By August 2005, MBTA was down to 32 active SLRVs,<ref>{{cite report |url=http://web.mit.edu/cron/project/uncertainty/BLUEBOOK/2005%20Blue%20Book%20Unabridged/2005%20Blue%20Book.pdf#page=20 |title=Ridership and Service Statistics |edition=Tenth |date=2005 |publisher=Massachusetts Bay Transportation Authority |access-date=27 December 2018}}</ref> and more were retired by February 2006.<ref>{{cite report |url=http://web.mit.edu/cron/project/uncertainty/BLUEBOOK/2006%20Blue%20Book/Bluebook%202006.PDF#page=11 |title=Ridership and Service Statistics |edition=Tenth revised |date=2006 |publisher=Massachusetts Bay Transportation Authority |access-date=27 December 2018}}</ref> The issues with Type 8 cars were finally resolved in 2006, allowing production and delivery to resume. By early 2007, a sufficient number of Type 8 cars had entered service to allow total retirement of the remaining Boeings. The final revenue service run of the MBTA Boeing cars was made on March 16, 2007,<ref name=Boeing/> on the Riverside Line by cars 3485 and 3499.<ref name=MBTA-roster /><ref>{{cite news |url=http://archive.boston.com/news/local/articles/2007/03/16/end_of_the_line_for_t_pioneers/ |title=End of the line for T pioneers |date=March 16, 2017 |newspaper=The Boston Globe |access-date=19 December 2018}}{{subscription required}}</ref> By late 2007, all Type 8s had been assembled and delivered for service.

===Muni===
[[File:Boeing and Breda cars at Geneva carhouse, May 1997.jpg|thumb|right|Boeing SLRV (LRV1) and Breda LRV2 at [[Balboa Park station]] (May 1997)]]
Muni began developing plans to procure replacements for the Boeing SLRVs in 1989.<ref name=Cartwright-96 /> A contract was signed with Italian manufacturer [[Società Italiana Ernesto Breda|Breda Costruzioni Ferroviarie]] on December 4, 1991, with an initial order of 35 cars and options for 20 more.<ref name=Callwell99>{{Muni Chronology}}</ref>{{rp|70–71}} San Francisco began retiring their Boeing SLRVs in 1995 after the first of their replacements (designated ''LRV2'') arrived from Breda. The newer Breda cars are more like what Muni wanted for its Muni Metro back in the early 1970s, before the design of the Boeing SLRV.<ref name="BoeingsForScrapOrSale!" />

At the end of 2001, Muni retired the last of their Boeing SLRVs after the LRV2s had proven to have improved reliability on the Muni Metro system.<ref name="BoeingsForScrapOrSale!" />

In contrast, Breda would not enjoy the same success in North American light rail, producing only the [[AnsaldoBreda P2550|P2550]] for Los Angeles and the aforementioned vehicles, and slightly more success with heavy rail, producing vehicles for [[Breda A650|Los Angeles]], 3 generations of vehicles for [[Washington Metro rolling stock|Washington]], and [[MARTA rail|Atlanta]].

==Disposition==

===Preserved in museums===
[[File:San Francisco Boeing LRV 1213 running at Oregon ERM in 2001.jpg|thumb|right|Car 1213 in operation at the Oregon Electric Railway Museum]]

Three US SLRVs have been saved in museums:
* ex-Muni 1213 at the [[Oregon Electric Railway Museum]] (acquired 2000)<ref name="BoeingsForScrapOrSale!" /><ref name=OERHS-1213>{{cite web |url=http://oerhs.oregontrolley.com/collection/car1213/ |title=Muni LRV 1213 |website=Oregon Electric Railway Historical Society |access-date=19 December 2018}}</ref>
* ex-Muni 1258 at the [[Western Railway Museum]] (acquired 2002)<ref>{{cite web |url=http://www.wrm.org/visit/car-roster/passenger-cars/interurban/item/111-san-francisco-municipal-railway-1258 |title=San Francisco Municipal Railway 1258 |date=May 5, 2011 |website=Western Railway Museum |access-date=19 December 2018}}</ref>
* ex-MBTA 3424 at the [[Seashore Trolley Museum]] (acquired 2009)<ref name="seashore-MBTA-3424"/>

Two others remained stored on Muni property for several years after retirement of the last cars from service, car 1320 at Geneva Division and car 1264 at the streetcar yard at Market and Duboce near the U.S. Mint<ref>[[:File:ARetiredBoeingVertolStreetcarAtPharrDivision-2.jpg|Photo of Muni Boeing car 1264 stored at Duboce Yard in 2007]]</ref> (but later also moved to Geneva).<ref>[https://www.google.com/maps/@37.7199563,-122.4472659,3a,51.3y,109.62h,84.24t/data=!3m6!1e1!3m4!1sSHuRgfzfTZtUu2Dt0Qoqkw!2e0!7i13312!8i6656  Both Boeings in Geneva yard, in 2015.]</ref>  These two cars remained stored until being scrapped in April 2016.<ref>{{cite news|last=Rodriguez|first=Joe Fitzgerald|url=http://www.sfexaminer.com/last-munis-1980s-era-clunker-trains-will-scrapped/|title=Last of Muni's 1980's-era clunker trains will be scrapped|date=March 31, 2016|newspaper=[[The San Francisco Examiner]]|access-date=2016-08-01|archive-date=April 24, 2016|archive-url=https://web.archive.org/web/20160424101013/http://www.sfexaminer.com/last-munis-1980s-era-clunker-trains-will-scrapped/|url-status=dead}}</ref> Another ex-Muni car (1271) is used as an office trailer at a Bay Area scrapyard.

The Seashore Trolley Museum had inquired about acquiring MBTA 3444, which was equipped with the plug door, for their collection, but did not take it because the car was not in operating condition and Seashore wanted an operating example. 3444 was missing several essential components, including one of the trucks, and was heavily rusted. 3444 was later scrapped in 2005 and Seashore instead acquired rehabilitated car 3424,<ref name="seashore-MBTA-3424">{{cite web|title=Massachusetts Bay Transportation Authority 3424|publisher=[[Seashore Trolley Museum]]|url=http://www.trolleymuseum.org/collection/browse.php?id=03424SMA|access-date=2017-05-04}}</ref> which was moved to the museum from MBTA's Riverside Yard on July 9, 2009.

===Manchester, UK===
[[File:San Francisco Muni, Boeing LRV 1226.jpg|thumb|right|Muni 1226 stored at [[Derby Litchurch Lane Works]]]]

In 2002, [[Manchester]] was the host city of the [[2002 Commonwealth Games|Commonwealth Games]]. Many of the venues used for the games were served by the [[Manchester Metrolink]], a regional light rail network which first opened in 1992. With capacity problems foreseen and thus requiring a short term solution, the [[Greater Manchester Passenger Transport Executive]] approached Muni about the possibility of buying redundant Boeing SLRVs. Two were purchased for $250 each for initial evaluation and shipped to England.<ref>Frisco trams for Manchester ''[[Rail (magazine)|Rail]]'' issue 423 November 28, 2001 page 19</ref><ref>Manchester Metro flies in Boeing trams ''[[The Railway Magazine]]'' issue 1210 February 2002 page 74</ref><ref>[https://web.archive.org/web/20190405073616/https://www.manchestereveningnews.co.uk/news/greater-manchester-news/metrolink-buys-old-us-trams-1193429 Metrolink buys old U.S. trams] ''[[Manchester Evening News]]'' February 17, 2007</ref>

Upon arrival in England in January 2002, 1226 was sent to [[Derby Litchurch Lane Works]] for assessment by [[His Majesty's Railway Inspectorate|Her Majesty's Railway Inspectorate]] to ensure it met UK safety standards, while 1326 was delivered directly to Metrolink's Queens Road Depot.<ref>From Frisco to Metro ''The Railway Magazine'' issue 1211 March 2002 page 101</ref><ref>First San Francisco Tram Arrives ''[[Railway World]]'' March 2002 page 9</ref> Muni cars 1214, 1219, 1220, 1221, 1234, 1249, 1268, 1288, 1305, 1308, 1312 and 1327 were stored in the US pending the sale.

Investigations concluded it was not economic to modify them for service in Manchester.<ref>Manchester says no to US trams ''The Railway Magazine'' issue 1219 November 2002 page 95</ref> The vehicle in Manchester was scrapped once the project was cancelled, while the vehicle in Derby was stored until 2016, at which point it too was broken up.<ref>{{cite web |url=http://www.britishtramsonline.co.uk/news/?p=14556 |title=The end of San Francisco trams in the UK? |last=Prior |first=Gareth |date=11 May 2016 |website=British Trams Online |access-date=28 October 2020 }}</ref>

===Working cars===
[[File:Green Line maintenance tram.jpg|thumb|right|Rerailer car #3417 on the MBTA [[Green Line E branch]] in 2007]]
The MBTA owned 3 decommissioned SLRV work cars until 2020, at which time they were scrapped:

*Rerailer car 3417
*Track geometry car 3448
*Maintenance of Way car 3453

Ex-MBTA car 3541 was donated to the [[United States Army]] for training in 2000. Ex-MBTA cars 3468, 3480, 3485, 3499, 3514, and 3520 were sold to the US Government and moved to the [[Transportation Technology Center]] in [[Pueblo, Colorado]] in 2010, for testing with real-life scenarios.<ref name=MBTA-roster />
{{clear}}

==See also==
* [[State-of-the-Art Car]]
* [[Canadian Light Rail Vehicle]]
* [[PCC streetcar]]

==References==
{{reflist}}

==External links==
{{Commons category}}
*[https://web.archive.org/web/20070222151636/http://members.aol.com/netransit/private/LRV.html Boston's Green Line Crisis] A summary of the problems faced by the MBTA with Boeing
*[https://web.archive.org/web/20031217180730/http://thethirdrail.net/0007/lrt1.htm 1975 article on rollout of US SLRV]
*[https://rosap.ntl.bts.gov/view/dot/520 US DOT UT 50009: Light Rail Transit: State of the Art Review (1976)]
*[https://web.archive.org/web/20000127064013/https://www.lightrail.com/carspecpages/mbta/mbtaboeing-vertol.htm MBTA US SLRV specs]
*[http://www.trolleymuseum.org/exhibits/state-art-cars/ SOAC1 & 2 at Seashore Trolley Museum]
*[http://www.nycsubway.org/cars/soac.html State of the Art Cars]
*{{cite report |doi=10.4271/740227 |chapter=The New United States Standard Light Rail Vehicle |author=Lenow, Martin |title=SAE Technical Paper Series |date=1974 |volume=1 |publisher=Society of Automotive Engineers}}
*{{cite journal |title=The Resurgence of Light Rail Transit |author=Lenow, Martin |date=1976 |journal=Transportation Engineering |publisher=ASCE |volume=102 |issue=2 |pages=229–242 |url=https://cedb.asce.org/CEDBsearch/record.jsp?dockey=0006678}}

===Advertisements===
*{{YouTube |id=N9fHJOcEOr4 |title=Vintage Boeing LRV Film, Part 1}}
*{{YouTube |id=xtto__LXZLc |title=Vintage Boeing LRV Film, Part 2}}
*[https://web.archive.org/web/20000609032134/http://members.aol.com/smoore5049/3418/ad.jpg 1977 ad for the US SLRV]

===Department of Transportation testing===
* {{cite report |url=https://archive.org/details/slrvengineeringt00boei_2 |title=SLRV engineering tests at Department of Transportation, Transportation Test Center: Final Test Report, No. UMTA-MA-06-0025-79-3 |volume=I |date=June 1979 |author=Boeing Vertol Company |publisher=U.S. Department of Transportation, Urban Mass Transportation Administration |access-date=18 December 2018}}
* {{cite report |url=https://archive.org/details/slrvengineeringt00boei_1 |title=SLRV engineering tests at Department of Transportation, Transportation Test Center: Final Test Report, No. UMTA-MA-06-0025-79-3 |volume=II |date=June 1979 |author=Boeing Vertol Company |publisher=U.S. Department of Transportation, Urban Mass Transportation Administration |access-date=18 December 2018}}
* {{cite report |url=https://archive.org/details/slrvengineeringt00boei_0 |title=SLRV engineering tests at Department of Transportation, Transportation Test Center: Final Test Report, No. UMTA-MA-06-0025-79-3 |volume=III |date=June 1979 |author=Boeing Vertol Company |publisher=U.S. Department of Transportation, Urban Mass Transportation Administration |access-date=18 December 2018}}
* {{cite report |url=https://archive.org/details/slrvengineeringt00boei |title=SLRV engineering tests at Department of Transportation, Transportation Test Center: Final Test Report, No. UMTA-MA-06-0025-79-3 |volume=IV |date=June 1979 |author=Boeing Vertol Company |publisher=U.S. Department of Transportation, Urban Mass Transportation Administration |access-date=18 December 2018}}

{{DEFAULTSORT:Us Standard Light Rail Vehicle}}
[[Category:Light rail vehicles]]
[[Category:Articulated passenger trains]]
[[Category:Electric multiple units of the United States]]
[[Category:Light rail in the United States]]
[[Category:Streetcars of the United States]]
[[Category:Green Line (MBTA)]]
[[Category:Muni Metro]]
[[Category:600 V DC multiple units]]