View source for Top Fuel

{{Short description|Type of drag racing motorsport}}
[[File:Top Fuel.JPG|thumb|right|upright=1.5|Two Top Fuel dragsters side by side during an NHRA event in 2012]]

'''Top Fuel''' is a type of [[drag racing]] whose [[Dragster (car)|dragster]]s are the quickest accelerating racing cars in the world and the fastest sanctioned category of drag racing, with the fastest competitors reaching speeds of {{convert|341.58|mph|km/h|1}} and finishing the {{convert|1,000|foot|m|1}} runs in 3.641 seconds.

A top fuel dragster accelerates from a standstill to {{Convert|100|mph|km/h|1|abbr=on}} in as little as 0.8 seconds (less than one third the time required by a production [[Porsche 911 Turbo]] to reach {{Convert|60|mph|km/h|1|abbr=on}})<ref>{{cite web|last1=Clarke|first1=John|title=Just how fast is a Top Fuel drag car?|url=http://www.nobbyville.com/TopFuel.htm|website=NobbyVille.com|publisher=John Clarke|access-date=8 November 2015}}</ref> and can exceed {{Convert|297|mph|km/h|1|abbr=on}} in just {{Convert|660|ft|m|1}}. This subjects the driver to an average acceleration of about {{convert|4.0|g0|lk=on|abbr=on}} over the duration of the race and with a peak of over {{convert|5.6|g0|lk=on|abbr=on}}.

Because of the speeds, this class races a {{convert|1000|foot|m|1}} distance, not the traditional drag-race length of one-fourth of a statute mile, or {{Convert|1320|ft|m|1}}. The rule was introduced in 2008 by the [[National Hot Rod Association]] after the fatal crash of [[Funny Car]] driver [[Scott Kalitta]] during a qualifying session at [[Old Bridge Township Raceway Park]] in [[Englishtown, New Jersey]]. The shortening of the distance was used by the [[FIA]] at some tracks, and as of 2012 is now the standard Top Fuel distance defined by the FIA. The [[International Hot Rod Association]], which at the time sanctioned Top Fuel in Australia, dropped the 1/4-mile distance in September 2017 after a campaign by Santo Rapisarda, a car owner who often runs NHRA races in the United States.

==Top Fuel racing==
[[File:2009NHRATopFuelChampTrophyTonySchumacher.jpg|thumb|upright|left|2009 NHRA Top Fuel championship trophy]]
Before their run, racers often perform a [[burnout (vehicle)|burnout]] to clean and heat tires. The burnout also applies a layer of fresh rubber to the track surface, improving traction during launch.

At maximum throttle and RPM, the exhaust gases escaping from a dragster's open [[Exhaust manifold|headers]] produce about {{convert|900|–|1100|lbf|kN|1}} of [[downforce]]. The massive airfoil over and behind the rear wheels produces much more, peaking at around {{convert|12000|lbf|kN|1}} when the car reaches about {{convert|330|mi/h|km/h|1|abbr=on}}.

The engine of a Top Fuel dragster generates around 150&nbsp;dB<ref>{{Cite web|url=https://www.espn.com/espn/news/story?id=5759488|title=The Mag: Drag racing, the loudest sport|date=2010-11-05|website=ESPN.com|access-date=2016-07-24}}</ref> of sound at full throttle, enough to cause physical pain or even permanent damage. Before a run, race announcers usually advise spectators to cover or plug their ears. Ear plugs and even earmuffs are often handed out to fans at the entrance of a Top Fuel event.

Dragsters are limited to a wheelbase of {{convert|300|in|m|1}}.

The most prolific active driver in Top Fuel is [[Tony Schumacher (drag racer)|Tony Schumacher]] and the most successful crew chief is Alan Johnson, who was the crew chief for six of Schumacher's championships, the back-to-back titles won by driver [[Gary Scelzi]] and was the crew chief for his brother [[Blaine Johnson|Blaine]] for his entire professional career.{{citation needed|date=November 2018}} The first female driver in the Top Fuel category is also the most associated female in the drag racing world, [[Shirley Muldowney]], who won three championships during her career.{{citation needed|date=November 2018}}

==Fuel==
Since 2015, [[NHRA]] regulations limit the composition of the fuel to a maximum of 90% [[nitromethane]]; the remainder is largely [[methanol]]. However, this mixture is not mandatory, and less nitromethane may be used if desired. While nitromethane has a much lower [[energy density]] ({{Convert|11.2|MJ/kg|Mcal-th/lb|abbr=on}}) than either gasoline ({{Convert|44|MJ/kg|Mcal-th/lb|abbr=on}}) or methanol ({{Convert|22.7|MJ/kg|Mcal-th/lb|abbr=on}}), an engine burning nitromethane can produce up to 2.4 times as much power as an engine burning gasoline. This is made possible by the fact that, in addition to fuel, an engine needs oxygen in order to generate force: the stoichiometric ratio of petrol is 14.7:1 air to petrol, and 1.7:1 air to nitromethane, which, unlike gasoline, already has oxygen in its molecular composition. For a given amount of air consumed, this means that an engine can burn 7.6 times more nitromethane than gasoline.

Nitromethane also has a high latent [[heat of vaporization]], meaning that it will absorb substantial engine heat as it vaporizes, providing an invaluable cooling mechanism. The laminar [[flame speed]] and combustion temperature are higher than gasoline's at {{Convert|0.5|m/s||abbr=on}} and {{Convert|2400|C|}} respectively. Power output can be increased by using very rich air-fuel mixtures. This also helps prevent [[Engine knocking|pre-ignition]], which is often a problem when using nitromethane.

Because of the relatively slow burn rate of nitromethane, very rich fuel mixtures are often not fully ignited, and some remaining nitromethane can escape from the exhaust pipe and ignite on contact with atmospheric oxygen, burning with a characteristic yellow [[flame]]. Additionally, after sufficient fuel has been combusted to consume all available oxygen, nitromethane can combust in the absence of atmospheric oxygen, producing [[hydrogen]], which can often be seen burning from the exhaust pipes at night as a bright white flame. In a typical run the engine can consume between {{convert|12|USgal|L|2}} and {{convert|22.75|USgal|L|2}} of fuel during warmup, burnout, staging, and the quarter-mile run.<ref>{{cite web|title=NHRA 101|url=http://www.nhra.com/nhra-101|website=NHRA.com|publisher=National Hot Rod Association|access-date=21 March 2017}}</ref><ref>{{cite web|last1=Smith|first1=Jeff|last2=Asher|first2=Jon|title=8,000HP Top Fuel Engine|url=http://www.hotrod.com/how-to/engine/ccrp-1009-8000hp-top-fuel-engine/|website=Hot Rod Network|publisher=Hot Rod Network. TEN: The Enthusiast Network.|access-date=7 September 2015|date=1 September 2010}}</ref><ref>{{cite web|title=Top Fuel by the Numbers|url=http://www.motortrend.com/features/112_0502_top_fuel_numbers/viewall.html|website=MotorTrend Magazine|publisher=TEN: The Enthusiast Network|access-date=7 September 2015|date=February 2005}}</ref>

==Top Fuel engines==
[[Image:Top Fuel engine.jpg|thumb|right|Engine of a top fuel car]]
{{more citations needed section|date=June 2024}}

===Rules===
Like many other motor sport formulas originating in the United States, [[NHRA]]-sanctioned drag racing favors heavy restrictions on engine configuration, sometimes to the detriment of technological development. In some cases, teams are required to use technologies that may be decades old,{{which|date=November 2018}} resulting in cars that may seem substantially less advanced than the average family car. However, while some basic facets of engine configuration are heavily restricted, other technologies, such as [[fuel injection]], clutch operation, ignition, and car materials and design, are under constant development.<ref>{{cite web|last=Jodauga|first=John|url=http://www.nhra.com/userfiles/file/ndlivefiles/features/TFInnov.pdf|title=Top 10 Top Fuel Innovations|access-date=5 September 2015|url-status=dead|archive-url=https://web.archive.org/web/20150906115238/http://www.nhra.com/userfiles/file/ndlivefiles/features/TFInnov.pdf|archive-date=6 September 2015}}</ref>

NHRA competition rules limit the [[engine displacement]] to {{convert|500|cuin|L|2}}. A {{convert|4.1875|in|mm|2|adj=on}} bore with a {{convert|4.5|in|mm|2|adj=on}} stroke are customary dimensions. Larger bores have been shown to weaken the cylinder block.{{Citation needed|date=June 2011}} [[Compression ratio]] is about 6.5:1,{{Citation needed|date=September 2010}} as is common on engines with overdriven [[Roots-type supercharger|Roots-type]] [[supercharger]]s.

===Engine===
The engine used to power a Top Fuel drag racing car is based on a second generation Chrysler RB Hemi, but is built exclusively of specialized parts. It retains the basic configuration with two valves per cylinder activated by [[pushrod]]s from a centrally-placed camshaft. The engine has [[hemispherical combustion chamber]]s, a 58-degree in. to ex. valve stem angle; {{convert|4.8|in|mm|2}} bore pitch.

The [[Cylinder block|block]] is [[CNC machine|machined]] from a piece of [[forging|forged]] aluminum. It features press-fitted, ductile iron cylinder liners. There are no water passages in the block, which adds considerable strength and stiffness. The engine is cooled by the incoming air/fuel mixture and the lubricating oil. Like the original Hemi, the racing cylinder block has a deep skirt for strength. There are five main bearing caps, which are fastened with aircraft-standard-rated steel studs, with additional reinforcing main studs and side bolts ("[[cross-bolted bearing|cross-bolting]]"). There are three approved suppliers of these custom blocks; [[Keith Black (engineer)|Keith Black]], Brad Anderson, and Alan Johnson.

The [[cylinder head]]s are machined from aluminum [[Billet (manufacturing)|billets]]. As such, they, too, lack water jackets and rely entirely on the incoming air/fuel mixture and lubricating oil for their cooling. The original Chrysler design of two large valves per cylinder is used. The intake valve is made from solid [[titanium]] and the exhaust from solid [[Nimonic|Nimonic 80A]] or similar. Seats are of [[ductile iron]]. [[Beryllium copper|Beryllium-copper]] has been tried but its use is limited due to its toxicity. Valve sizes are around {{convert|2.45|in|mm|2|abbr=on}} for the intake and {{convert|1.925|in|mm|2|abbr=on}} for the exhaust. In the ports there are integral tubes for the push rods. The heads are sealed to the block by copper gaskets and [[stainless steel]] [[o-ring]]s.  Securing the heads to the block is done with aircraft-rated steel studs and stud nuts.

The camshaft is billet steel, made from 8620 carbon or S7 through-hardened tool steel or similar. It runs in five oil pressure lubricated bearing shells and is driven by gears in the front of the engine. Mechanical roller lifters ([[cam follower]]s) ride atop the cam lobes and drive the steel push rods up into the steel [[rocker arm]]s that actuate the valves. The rockers are of roller tip type on the intake and exhaust sides. Like the cam follower rollers, the steel tip roller rotates on a steel roller bearing and the steel rocker arms rotate on a pair of through-hardened tool steel shafts within bronze bushings. Intake and exhaust rockers are billet. The dual [[Poppet valve|valve springs]] are of coaxial type and made out of titanium. Valve retainers are also made of titanium, as are the rocker covers.

Billet steel [[crankshaft]]s are used; they all have a [[crossplane|cross plane]] a.k.a. 90 degree configuration and run in five conventional bearing shells. [[V8 engine#Design|180 degree crankshaft]]s have been tried. Due to ease of laying out an exhaust system with even pulsation, the 180 degree crankshaft can offer increased power in engines with interacting exhaust. However this does not concern Top Fuel engines with separate exhaust pipes for each cylinder. A 180 degree crankshaft is about {{Convert|10|kg||abbr=on}} lighter than 90 degree crankshaft, but they create a lot of vibration. Such is the strength of a top fuel crankshaft that in one incident, the entire engine block was split open and blown off the car during an engine failure, and the crank, with all eight connecting rods and pistons, was left still bolted to the clutch.

[[Piston]]s are made of forged aluminum. They have three [[Piston ring|ring]]s and aluminum buttons retain the {{convert|1.156|x|3.300|in|mm|2|abbr=on}} steel wrist pin. The piston is [[anodize]]d and [[Polytetrafluoroethylene|Teflon]] coated to prevent [[galling]] during the high thrust load operation encountered. The top ring is an L-shaped section "Dykes" ring that provides the best seal during combustion, but a second ring must be used to prevent excessive oil from entering the combustion chamber during intake strokes, as the Dykes-style ring offers less than optimal reverse gas/oil sealing. The third ring is an oil scraper ring whose function is to scrape the majority of the oil film off the cylinder wall as the piston descends from top dead center (TDC), to prevent oil being exposed to combustion heat and contaminating the upcoming round of fuel/air. This "oil scraping" also provides a key heat removal step for the cylinder walls and piston skirts; the oil film is renewed as the piston moves upward after reaching bottom dead center (BDC).

The [[connecting rod]]s are of forged aluminum and do provide some shock damping, which is why aluminum is used in place of titanium, {{citation needed span|date=September 2010|because titanium connecting rods transmit too much of the combustion impulse to the big-end rod bearings,}} endangering the bearings and thus the crankshaft and block. Each con rod has two bolts, shell bearings for the big end while the pin runs directly in the rod.{{Citation needed|date=September 2010}}

===Superchargers===
The [[supercharger]] must be a 14-71 type [[Roots blower]]. It has twisted lobes and is driven by a [[toothed belt]]. The supercharger is slightly offset to the rear to provide an even distribution of air. Absolute [[manifold pressure]] is usually {{convert|56|-|66|psi|kPa|0}}, but up to {{convert|74|psi|kPa|0}} is possible. The manifold is fitted with a {{convert|200|psi|kPa|0}} [[Rupture disc|burst plate]]. Air is fed to the compressor from [[throttle]] butterflies with a maximum area of {{cvt|65|sqin|mm2|0}}. At maximum pressure, it takes approximately {{convert|1000|hp|kW|-1}} to drive the supercharger.

These superchargers are in fact derivatives of [[General Motors]] scavenging-air blowers for their [[Detroit Diesel Series 71|two-stroke diesel engine]]s, which were adapted for automotive use in the early days of the sport. The model name of these superchargers delineates their size &ndash; the once commonly used 6-71 and 4-71 blowers were designed for General Motors diesels having six cylinders of {{convert|71|cuin|L|2|abbr=on}} each, and four cylinders of {{convert|71|cuin|L|2|abbr=on}} each, respectively. Thus, the currently used 14-71 design can be seen to be a huge increase in power delivery over the early designs, purpose-built for the GM Detroit Diesel truck powerplants.

Mandatory safety rules require a secured Kevlar-style blanket over the supercharger assembly as "blower explosions" are not uncommon, from the volatile air/fuel mixture coming from the [[fuel injector]]s being drawn directly through them. The absence of a protective blanket exposes the driver, team and spectators to shrapnel in the event that nearly any irregularity in the induction of the air/fuel mixture, the conversion of combustion into rotating crankshaft movements, or in the exhausting of spent gasses is encountered.

===Oil and fuel systems===
The oil system has a [[wet sump]] which contains {{Convert|16|usqt|l|1}} of SAE 70 mineral or synthetic racing oil. The pan is made of titanium or aluminum. Titanium can be used to prevent oil spills in the event of a blown rod.  Teams are fined and points are lost if oil is spilled on the track surface, so all teams make provision for absorbent blankets/diapers below the engine.  [[Oil pump (internal combustion engine)|Oil pump]] pressure is somewhere around {{convert|160|–|170|psi|kPa|-1|abbr=on}} during the run, {{convert|200|psi|kPa|-1|abbr=on}} at start up, but actual figures differ between teams.

Fuel is injected by a [[Fuel injection#Multi-point injection|constant flow injection]] system. There is an engine driven mechanical fuel pump and about 42 fuel nozzles. The pump can flow {{convert|100|usgal|L|-1}} per minute at 7500 rpm and {{convert|500|psi|kPa|-1|abbr=on}} fuel pressure. In general 10 injectors are placed in the injector hat above the supercharger, 16 in the intake manifold and two per cylinder in the cylinder head. Usually a race is started with a leaner mixture, then as the clutch begins to tighten as the engine speed builds, the air/fuel mixture is enriched. As the increased engine speed builds up pump pressure, the mixture is made leaner to maintain a predetermined ratio that is based on many factors, especially race track surface friction. The [[stoichiometry]] of both [[methanol]] and [[nitromethane]] is considerably greater than that of racing gasoline, as they have oxygen atoms attached to their carbon chains and gasoline does not. This means that a "fueler" engine will provide power over a very broad range from very lean to very rich mixtures. Thus, to attain maximum performance, before each race, by varying the level of fuel supplied to the engine, the mechanical crew may select power outputs barely below the limits of tire traction. Power outputs which create tire slippage will "smoke the tires" and as a result the race is often lost.

===Ignition and timing===
The air/fuel mixture is ignited by two {{Convert|14|mm||abbr=on|adj=on}} [[spark plug]]s per cylinder. These plugs are fired by two 44-[[ampere]] [[magneto (electrical)|magnetos]]. Normal [[ignition timing]] is 58-65 degrees [[BTDC]] (This is dramatically greater [[spark advance]] than in a petrol engine as "nitro" and alcohol burn far slower). Directly after launch the timing is typically decreased by about 25 degrees for a short time as this gives the tires time to reach their correct shape. The ignition system limits the engine speed to 8400 rpm. The ignition system provides initial 60,000 volts and 1.2 amperes. The long duration spark (up to 26 degrees) provides energy of {{Convert|950|mJ|cal-th|lk=in}}. The plugs are placed in such a way that they are cooled by the incoming charge. The ignition system is not allowed to respond to real time information (no computer-based spark lead adjustments), so instead a timer-based retard system is used.

===Exhaust===
The engine is fitted with eight individual open exhaust pipes, {{convert|2.75|in|mm|2|abbr=on}} in diameter and {{convert|18|in|mm|2|abbr=on}} long. These are made of [[steel]] and fitted with [[thermocouple]]s for measuring of the [[exhaust gas temperature]]. They are called "zoomies" and exhaust gases are directed upward and backwards. Exhaust temperature is about {{convert|500|F|C|0}} at idle and {{convert|1796|F|C|0}} by the end of a run.  During a nighttime event, the slow-burning nitromethane can be seen to extend flames many feet out from the exhaust pipes.

The engine is warmed up for about 80 seconds. After the warm up the [[valve cover]]s are taken off, oil is changed and the car is refueled. The run including tire warming is about 100 seconds which results in a "lap" of about three minutes. After each lap, the entire engine is disassembled and examined, and worn or damaged components are replaced.

===Performance===
Measuring the power output of a top fuel engine directly is not always feasible. Certain models use a torque sensor incorporated as part of the RacePak data system. [[Dynamometer]]s that can measure the output of a Top Fuel engine exist; however, the main limitation is that a Top Fuel engine cannot be run at its maximum power output for more than 10 seconds without overheating or possibly destroying itself explosively. Making such high power levels from such relatively limited displacement is a result of using very high boost levels and running at extremely high RPMs; both of these stress the internal components to a high degree, meaning that the peak power can only safely be achieved for brief periods of time, and even then only by intentionally sacrificing components. The engine power output can also be calculated based upon the car's weight and its performance. The calculated [[Power (physics)|power]] output of these engines is most likely somewhere between {{convert|8500|and|10000|hp|kW|-1|abbr=on}},<ref>{{cite web|title=FORGET 8,000 HORSEPOWER ... TOP FUEL IS NOW OVER 10,000 HORSEPOWER!|url=http://www.tmcnet.com/usubmit/2014/08/02/7952726.htm|website=TMC News|access-date=24 June 2015}}</ref> which is about twice as powerful as the engines installed on some modern [[diesel locomotive]]s, with a [[torque]] output of approximately {{convert|7400|lbfft|Nm|-1|lk=on}}<ref>{{Cite web|url=http://www.nfvzone.com/news/2014/08/02/7952726.htm|title=FORGET 8,000 HORSEPOWER ... TOP FUEL IS NOW OVER 10,000 HORSEPOWER! [National Dragster]|website=www.nfvzone.com|access-date=2016-07-24}}</ref> and a [[Mean effective pressure|brake mean effective pressure]] of {{convert|1160|-|1450|psi|MPa|0|abbr=on}}.

In late 2015, tests using sensors developed by [[AVL Racing]] showed peak power of over {{Convert|11,000|hp|kW|-1|abbr=on}}.<ref>{{cite web|last1=Magda|first1=Mike|title=Test Shows Top Fuel Nitro Engine Makes Over 11,000 Horsepower|url=http://www.enginelabs.com/news/video-test-shows-top-fuel-nitro-engine-makes-over-11000-horsepower/|website=Engine Labs|date=8 December 2015|access-date=2 May 2016}}</ref>

For the purposes of comparison, a 2009 [[SSC Aero|SSC Ultimate Aero TT]], which at the time was among the world's most powerful production automobiles, produces {{convert|1287|hp|kW|0|abbr=on}} of power and {{convert|1112|lbfft|Nm|0|abbr=on}} of torque.

From start to finish the engine will turn 240 revolutions. Including start up, burnout, staging and the race, the engine must survive just 500 revolutions before being rebuilt.{{Citation needed|date=January 2022}} This calculation assumes an average racing engine speed of roughly 3,800 revolutions per minute over a period of 3.8 seconds.

===Engine weight===
*Block with liners {{convert|187|lb|kg|1|abbr=on}}
*Heads {{convert|40|lb|kg|1|abbr=on}}  each
*Crankshaft {{convert|81.5|lb|kg|1|abbr=on}}
*Complete engine {{convert|496|lb|kg|0|abbr=on}}

==Mandatory safety equipment==
Much of organized drag-racing is sanctioned by the National Hot Rod Association.  Since 1955, the association has held regional and national events (typically organized as single elimination tournaments, with the winner of each two car race advancing) and has set rules for safety, with the more powerful cars requiring ever more safety equipment.

Typical safety equipment for contemporary top fuel dragsters:  full face helmets with fitted [[HANS device]]s; multi-point, quick release safety restraint harness; full body [[fire suit]] made of [[Nomex]] or similar material, complete with face mask, gloves, socks, shoes, and outer sock-like boots, all made of fire-resistant materials; on board fire extinguishers; kevlar or other synthetic "bullet-proof" blankets around the superchargers and clutch assemblies to contain broken parts in the event of failure or explosion; damage resistant fuel tank, lines, and fittings; externally accessible fuel and ignition shut-offs (built to be accessible to rescue staff); braking parachutes; and a host of other equipment, all built to the very highest standards of manufacturing.  Any breakthrough or invention that is likely to contribute to driver, staff, and spectator safety is likely to be adopted as a mandated rule for competition.  The 54-year history of NHRA has provided hundreds of examples of safety upgrades.

In 2000, the NHRA mandated the maximum concentration of nitromethane in a car's fuel be no more than 90%.  In the wake of a [[Gateway International Raceway]] fatality in 2004, involving racer [[Darrell Russell (drag racer)|Darrell Russell]], the fuel ratio was reduced to 85%.  Complaints from teams in regards to cost, however, has resulted in the rule being rescinded starting in 2008, when the fuel mixture returns to 90%, as NHRA team owners, crew chiefs, and suppliers complained about mechanical failures that can result in oildowns or more severe crashes caused by the reduced nitromethane mixture. They also mandated enclosed roll cages.<ref>[http://www.nhra.com/content/news/24145.htm NHRA News: Nitro percentage to be raised to 90 in Top Fuel, Funny Car in 2008 (9/15/2007)<!-- Bot generated title -->]{{dead link|date=February 2018 |bot=InternetArchiveBot |fix-attempted=yes }}</ref>

The NHRA also mandated that different rear tires be used to reduce failure, and that a titanium "shield" be attached around the back-half of the roll-cage to prevent any debris from entering the cockpit. This also was the result of the fatal crash at Gateway International Raceway. The rear tire pressure is also heavily regulated by [[Goodyear Tire and Rubber]] on behalf of the NHRA, at {{Convert|7|psi|kPa|0|abbr=on}}, the absolute minimum pressure allowed.

At present, final drive ratios higher than 3.20 (3.2 engine rotations to one rear axle rotation) are prohibited, in an effort to limit top speed potential, thus reducing the level of danger.

== History ==
In 1958, NHRA banned nitro in all categories; the American Hot Rod Association (AHRA) still allowed it, and Fuel Dragsters (FD), Hot Roadsters (HR), and Fuel Coupés (FC):  this led to [[Altered (drag racing)|Fuel Altered]]s (AA/FAs), [[A/FX|Factory Experimental]]s (A/FXs), and (ultimately) [[Funny Car]]s (TF/FCs).<ref>McClurg, Bob. ''Diggers, Funnies, Gassers and Altereds: Drag Racing's Golden Age''. (CarTech Inc, 2013), p.46.</ref>

Independent drag strips, not NHRA sanctioned, offered venues for the fuel racers.<ref>McClurg, ''Diggers'', p.46.</ref> [[Smokers Car Club]] hosted the first U.S. Fuel and Gas Championship at [[Famoso Raceway]] in March 1959.<ref>McClurg, ''Diggers'', p.46.</ref> [[Bob Hansen]] won Top Fuel Eliminator (TFE) in his A/HR, with a speed of {{convert|136|mph|km/h|1|abbr=on}}.<ref>McClurg, ''Diggers'', p. 46.  McClurg does not mention his e.t.</ref>

[[Jimmy Nix]], who previously ran a Top Gas dragster; [[Jim Johnson (drag racer)|Jim Johnson]], who ran a [[Dodge Polara]] [[Stock (drag racing class)|stocker]], and who had won the B/SA title in 1963; [[Jim Nelson (drag racer)|Jim Nelson]]; and [[Dode Martin]] pioneered TF/FC.<ref>McClurg, Bob.  "50 Years of Funny Cars:  Part 2" in ''Drag Racer'', November 2016, p.35; Burgess, Phil ''National Dragster'' Editor. "Early Funny Car History 101", written 22 January 2016, at [http://www.nhra.com/news/2016/early-funny-car-history-101 NHRA.com] (retrieved 23 May 2017)</ref> (Nix tried to persuade Chrisman to get Mercury Racing Director Fran Hernandez to allow him to run his Comet's 427 on nitro, as a way to gain leverage on NHRA, so Nix could use nitro himself).<ref>Burgess, Phil ''National Dragster'' Editor. "Early Funny Car History 101", written 22 January 2016, at [http://www.nhra.com/news/2016/early-funny-car-history-101 NHRA.com] (retrieved 23 May 2017)</ref>  These cars ran in NHRA's S/FX class, variously defined as "Super Factory Experimental" or "Supercharged Factory Experimental".<ref>Burgess, Phil ''National Dragster'' Editor. "Early Funny Car History 101", written 22 January 2016, at [http://www.nhra.com/news/2016/early-funny-car-history-101 NHRA.com] (retrieved 23 May 2017)</ref>

They were shortly turning in E.T.s in the low 11s and trap speeds of over {{convert|140|mph|km/h|1|abbr=on}}; at Long Beach on 21 March, an 11.49 pass at {{convert|141.66|mph|km/h|1|abbr=on}} was recorded.<ref>Wallace, Dave.  "50 Years of Funny Cars" in ''Drag Racer'', November 2016, p.22 and caption.</ref>

Bob Sullivan's [[Pandemonium (Funny Car)|''Pandemonium'']] (a '65 [[Plymouth Barracuda]]) joined about six other nitro-fuelled early funny cars facing fuel dragsters in the 1965 season.<ref>Wallace, p.30 caption.</ref>

In 1971, [[Don Garlits]] introduced the ''Swamp Rat XIV'', a rear-engined Top Fuel dragster. While others had been developed in the previous decade, it was the first successful one, winning the [[1971 NHRA Winternationals]].<ref>{{cite magazine |magazine=Hot Rod |date=Dec 1986 |page=28}}</ref><ref>Front to back: The rear-engine transition ([https://www.nhra.com/news/2015/front-back-rear-engine-transition Part 1], [https://www.nhra.com/news/2015/front-back-rear-engine-transition-part-2 Part 2]) - Phil Burgess, NHRA, February 2015</ref>

In 1984, Top Fuel was at a low point. It was having trouble attracting full sixteen-car fields, leading to cutting back to eight-car rosters, while the [[International Hot Rod Association]] dropped Top Fuel entirely.<ref>Ganahl, Pat. "Winter Heat: '87 NHRA Wnternationals", in ''Hot Rod'', May 1987, p.88.</ref> The same year, [[Joe Hrudka]] offered a major purse, the [[Cragar]]-[[Weld Wheels|Weld]] Top Fuel Classic and [[Don Garlits|"Big Daddy" Don Garlits]] returned to Top Fuel full-time.<ref>Ganahl, Pat. "Winter Heat: '87 NHRA Wnternationals", in ''Hot Rod'', May 1987, p.88.</ref> By 1987, NHRA Top Fuel Funny Car was drawing twice as many entrants as positions available.<ref>Ganahl, Pat. "Winter Heat: '87 NHRA Wnternationals", in ''Hot Rod'', May 1987, p.88.</ref>

In 2012 enclosed cockpits were allowed to be used regularly in top fuel by the NHRA.<ref>{{Cite web |title=NHRA approves enclosed cockpit for Top Fuel dragster use |url=https://sports.yahoo.com/blogs/nascar-from-the-marbles/nhra-approves-enclosed-cockpit-top-fuel-dragster-020508556--nascar.html |access-date=2023-01-05 |website=sports.yahoo.com |language=en-US}}</ref>

==Most NHRA Top Fuel wins==
{| class="wikitable"
|+
! colspan="4" |'''Key'''
|-
|**
| colspan="3" |Denotes active driver
|}
{| class="wikitable"
! Driver !! Wins
|-
| [[Tony Schumacher (drag racer)|Tony Schumacher]]** || 88
|-
| [[Antron Brown]]** || 65
|-
| [[Larry Dixon (dragster driver)|Larry Dixon]] || 62
|-
| [[Steve Torrence]]** || 56
|-
| [[Doug Kalitta]]** || 55
|-
| [[Joe Amato (dragster driver)|Joe Amato]] || 52
|-
| [[Kenny Bernstein]] ||  39
|-
| [[Don Garlits]] || 35
|-
| Cory McClenathan || 34
|-
| [[Gary Scelzi]] || 29
|-
| Shawn Langdon** || 19
|-
| [[Gary Beck]] || 19
|-
| Darrell Gwynn || 18
|-
| [[Brandon Bernstein]] || 18
|-
| Spencer Massey || 18
|-
| [[Shirley Muldowney]] || 18
|-
| [[Brittany Force]]** || 18
|-
| [[Scott Kalitta]] || 17
|-
| Justin Ashley || 16
|-
| Dick Lahaie || 15
|-
| Gary Ormsby || 14
|-
| [[Don Prudhomme]] || 14
|-
| [[Eddie Hill]] || 13
|-
| Mike Dunn || 12
|-
| Morgan Lucas || 12
|-
| [[Leah Pruett]] || 12
|-
| Doug Herbert || 10
|-
| [[Connie Kalitta]] || 10
|-
| Richie Crampton || 10
|-
| J.R. Todd** || 9 
|-
| Mike Salinas || 9
|-
| Jeb Allen || 9
|-
| Del Worsham || 8
|-
| Billy Torrence || 8
|-
| Clay Millican** || 8
|-
| Rod Fuller || 7
|-
| Darrell Russell || 6
|-
| Pat Austin || 5
|-
| Austin Prock** || 4
|-
| Blaine Johnson || 4 
|-
| Khalid alBalooshi || 4
|-
| David Grubnic || 4
|-
| [[Melanie Troxel]] || 4
|-
| Lori Johns || 4
|-
| Shelly Anderson Payne || 4
|-
| Gene Snow || 3
|-
| Bob Vandergriff Jr. || 3
|-
| Jim Head || 3
|-
| Pat Dakin || 2
|-
| Tommy Johnson Jr || 2
|-
| Frank Hawley || 2
|-
| Terry McMillen || 2
|-
| Blake Alexander** || 2
|-
| [[Josh Hart (racer)|Josh Hart]]** || 2
|-
| Mark Oswald || 2
|-
| [[Tony Stewart]]** || 2
|-
| Tripp Tatum** || 1
|-
| Hillary Will || 1
|-
| Cristen Powell || 1
|-
| Lucille Lee || 1
|-
| [[Ron Capps (racing driver)|Ron Capps]]** || 1
|-
| Tom McEwen || 1
|-
| Ed McCulloch || 1
|-
| Terry Capp || 1
|-
| Michael Brotherton || 1
|-
| Johnny Abbott || 1
|-
| Jim Barnard || 1
|-
| Jody Smart || 1
|-
| Dwight Salisbury || 1
|-
| Dan Pastorini || 1
|-
| Bill Mullins || 1
|-
| Rance McDaniel || 1
|-
| Chip Woodall || 1
|-
| Jack Williams || 1
|-
| John Wiebe || 1
|-
| Hank Westmoreland || 1
|-
| Jim Walther || 1
|-
| Stan Shiroma || 1
|-
| Dave Settles || 1
|-
| Rick Ramsey || 1
|-
| Herm Petersen || 1
|-
| Carl Olsen || 1
|-
| Bob Noice || 1
|-
| Jimmy Nix || 1
|-
| John Mulligan || 1
|-
| Don Moody || 1
|-
| Ronnie Martin || 1
|-
| Art Marshall || 1
|-
| Jimmy King || 1
|-
| Hank Johnson || 1
|-
| Clayton Harris || 1
|-
| Gerry Glenn || 1
|-
| Bob Gibson || 1
|-
| Larry Dixon Sr. || 1
|-
| Dave Chenevert || 1
|-
| Jim Bucher || 1
|-
| Arnie Behling || 1
|}

==See also==
* [[ANDRA Top Fuel]]

==References==
{{reflist}}
* {{cite journal|title=The Top Fuel V8|publisher=Race Engine Technology|issue=9|pages=60–69}}
* {{cite journal|title=Running the Army Motor|publisher=Race Engine Technology|issue=8|pages=60–69}}
* {{cite magazine|title=Top Fuel by the Numbers|last=Kiewicz|first=John|magazine=Motor Trend|issue=February 2005}}
* {{cite magazine|title=Drag Racing: It's Like Plunging Your Toilet with a Claymore Mine|last=Phillips|first=John|magazine=Car and Driver|issue=August 2002}}
* {{cite journal|title=Blown Nitro Racing on a Budget|last=Szabo|first=Bob|publisher=Szabo Publishing|issue=January 2013|url=http://racecarbook.com}}

==External links==
* [http://cacklefest.com/history-2000-CHRR.shtml Restored Top Fuel Dragsters from the 60s & 70s]
* [http://www.nhra.com NHRA National Hot Rod Association Website]
* [http://www.wsid.com.au WSID Website] {{Webarchive|url=https://web.archive.org/web/20130723132102/http://www.wsid.com.au/ |date=2013-07-23 }}
* [http://www.ihra.com IHRA International Hot Rod Association Website]
* [http://www.santapod.com Santa Pod Raceway] - the home of European Drag Racing

{{Class of Auto racing}}

[[Category:Drag racing classes]]