View source for Coupling rod

{{Distinguish|Connecting rod}}
{{Short description|Rod connecting driving wheels of a locomotive}}
{{Refimprove|date=January 2013}}
[[File:MILW 261 drivers.jpg|thumb|300px|Hinged side rods connecting the [[driving wheel]]s of [[Milwaukee Road 261]].]]
A '''coupling rod''' or '''side rod''' connects the [[driving wheel]]s of a [[locomotive]]. [[Steam locomotive]]s in particular usually have them, but some [[Diesel locomotive|diesel]] and [[Electric locomotive|electric]] locomotives, especially older ones and [[switcher locomotive|shunter locomotives]], also have them. The coupling rods transfer the power of drive to all wheels.

==Development==
[[Locomotion No. 1]] was the first locomotive to employ coupling rods rather than [[Chain drive|chains]]. In the 1930s reliable [[roller bearing]] coupling rods were developed.<ref>Tracy V. Buckwalter, Locomotive Drive, {{US patent|1951126}}, granted Mar. 13, 1934.</ref>
<!-- {{Reinhard Mirkovich|date=March 2008}} -->

==Allowance for vertical motion==
[[File:Wheel of locomotive.jpg|right|thumb|Connecting rod and coupling rods attached to a small locomotive driving wheel]]
In general, all railroad vehicles have [[Suspension (vehicle)|spring suspension]]; without springs, irregularities in the track could lift wheels off the rail and cause impact damage to both rails and vehicles. Driving wheels are typically mounted so that they have around 1 inch (2.5&nbsp;cm) of vertical motion. When there are only 2 coupled axles, this range of motion places only slight stress on the [[crank pin]]s. With more axles, however, provision must be made to allow each axle to move vertically independently of the others without bending the rods. This may be done by hinging the side rod at each intermediate crank pin, either using the pin itself as a [[hinge pin]],<ref>Robert Humble, Connecting-Rod, {{US patent|391,148}}, granted Oct. 16, 1888.</ref><ref>William G. Knight, Locomotive Driving Rod Connection, {{US patent|1807217}}, granted May 18, 1931.</ref> or adding a hinge joint adjacent to the pin, as shown in the illustration.

An alternative is to use a side rod that spans multiple axles with a [[scotch yoke]] used at each intermediate axle. This approach was quite common when side rods were used to link a [[Jackshaft (locomotive)|jackshaft]] to 2 or more [[driving wheel]]s on [[electric locomotive]]s and some early internal combustion locomotives. The Swiss [[Crocodile (locomotive)|Ce 6/8<sup>II</sup> Crocodile locomotive]] is a prominent example, but there were others.<ref>Archibald H. Ehle, Internal-Combustion Locomotive, {{US patent|951062}}, granted Mar. 1, 1910</ref><ref>General Construction, Baldwin Gasoline Industrial Locomotives [https://books.google.com/books?id=jHwiAQAAMAAJ&pg=PA57 Baldwin Locomotive Works Record], No. 74, 1913; pages 7-9.  The reason for the scotch yoke is given explicitly on page 8.</ref><ref>Norman W. Storer, Electric Locomotive, {{US patent|991038}}, granted May 2, 1911.</ref>

==Balancing==
[[File:Roues de Tem II 288 à la gare du Pont 18-08-2012 4.JPG|thumb|300px|Counterweight on a small [[Outside frame|outside-frame]] dual-mode [[electro-diesel locomotive]], a [[Swiss locomotive and railcar classification|Swiss]] Tem II [[shunter locomotive]].]]
The coupling rod's off-center attachment to the [[crank pin]] of the driving wheel inevitably creates an eccentric movement and vibration when in motion. To compensate for this, the driving wheels of an inside-frame locomotive always had built-in [[counterweight]]s to offset the angular momentum of the coupling rods, as shown in the figures above. On [[Outside frame|outside-frame]] locomotives, the counterweight could be on the driving wheel itself, or it could be on the crank outside the frame, as shown in the adjacent figure.

Where the motion of the side-rods is purely circular, as on locomotives driven by [[Jackshaft (locomotive)|jackshafts]] or geared transmission to one driver, counterweights can balance essentially all of the motion of the side rods. Where part of the motion is non-circular, for example, the horizontal motion of a piston rod, counterweights on the wheels or drive axles cannot be made to balance the entire assembly perfectly. On a driving wheel supporting both side-rods and the [[connecting rod]] to a [[piston]], the counterweight needed to balance the horizontal motion of the piston and connecting rod would be heavier than the counterweight needed to balance the vertical weight of the rods. As a result, a counterweight chosen to minimize the total vibration will not minimize the vertical component of the vibration.

The vertical component of the vibration that could not be eliminated because of the weight needed to balance the pistons is called [[Hammer blow|hammering]]. This is destructive to both the locomotive and the roadbed. In some locomotives, this hammering can be so intense that at speed, the drivers alternately jump from the rail head, then slam down hard on the rails as the wheels complete their rotation. Unfortunately, hammering is inherent to conventional two-cylinder piston-driven steam locomotives and that is one of the several reasons they have been retired from service.

==Materials==
Initially, coupling rods were made of [[steel]].{{Citation needed|date=March 2011}} As technology progressed and better materials became available, the connecting rods were manufactured of lighter and stronger [[alloy]]s{{Citation needed|date=April 2010}}, which in turn permitted smaller counterweights and also reduced hammering.

==References==
{{reflist}}

==See also==
{{Commons|Lokomotiven mit Stangenantrieb|Locomotives with coupling rod}}
* [[Steam locomotive components]]

[[Category:Locomotive parts]]
[[Category:Steam locomotive technologies]]